Reply
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Re: Unable to see new volume size
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2011-08-08
08:57 AM
2011-08-08
08:57 AM
Unable to see new volume size
Hello All,
=============================================================================
Disk 2 WDC WD20EARS-00MVWB0 1862 GB , 30 C / 86 F , Write-cache ON OK
Disk 4 WDC WD20EARS-00MVWB0 1862 GB , 28 C / 82 F , Write-cache ON
Model: ReadyNAS NV [X-RAID]
Serial: 000da2010164
Firmware: RAIDiator 4.1.7 [1.00a043]
Memory: 512 MB [2.5-3-3-7]
IPv4 address:: 192.168.0.110
Volume C: Online, X-RAID, Single disk, 0% of 1848 GB used
=============================================================================
I added the 2nd disk of same size (2TB) and the led light as well as web page shows 2 drives. But the above status shows i' using single disk and also in status page, it warns me that it could lead to failure due to missing redundant disk.
It has been more than 12 hours now and I still see same status, no status emails as of now.
I added the first disk 2TB, i set it up volumes etc (no data at all) and then added 2nd disk. Syncing new data should not be a problem for 0 byte data on both disks.
Please help me combine those 2 2TB disks. Thanks.
=============================================================================
Disk 2 WDC WD20EARS-00MVWB0 1862 GB , 30 C / 86 F , Write-cache ON OK
Disk 4 WDC WD20EARS-00MVWB0 1862 GB , 28 C / 82 F , Write-cache ON
Model: ReadyNAS NV [X-RAID]
Serial: 000da2010164
Firmware: RAIDiator 4.1.7 [1.00a043]
Memory: 512 MB [2.5-3-3-7]
IPv4 address:: 192.168.0.110
Volume C: Online, X-RAID, Single disk, 0% of 1848 GB used
=============================================================================
I added the 2nd disk of same size (2TB) and the led light as well as web page shows 2 drives. But the above status shows i' using single disk and also in status page, it warns me that it could lead to failure due to missing redundant disk.
It has been more than 12 hours now and I still see same status, no status emails as of now.
I added the first disk 2TB, i set it up volumes etc (no data at all) and then added 2nd disk. Syncing new data should not be a problem for 0 byte data on both disks.
Please help me combine those 2 2TB disks. Thanks.
Message 1 of 3
Labels:
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2011-08-11
03:59 AM
2011-08-11
03:59 AM
Re: Unable to see new volume size
can you open a tech support case? you can also try check the health tab and get the information of what the disk is doing.
You may also boot to factory default since there is no data in the NAS.
You may also boot to factory default since there is no data in the NAS.
Message 2 of 3
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2011-08-11
06:36 PM
2011-08-11
06:36 PM
Re: Unable to see new volume size
Thank you amac27. I did factory reset and now I got both disks in X-Raid setup.
Message 3 of 3