- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Re: EX8000 1.0.1.192 Firmware released
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
EX8000 1.0.1.192 Firmware released
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: EX8000 1.0.1.192 Firmware released
Did you install it, or are you waiting for others to take the risk and go first?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: EX8000 1.0.1.192 Firmware released
Wait for Release notes and then wait a other 2 day's.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: EX8000 1.0.1.192 Firmware released
I would load FW and then to a full factory reset and setup from scratch to ensure the FW gets installed well and a new configuration is put in place.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: EX8000 1.0.1.192 Firmware released
I finally bit the bullet and upgraded to .192.
Attached devices now show up on the page without having to do a refresh. A lot more of them are showing as <unknown>, but at least they are showing up. I will comment about stability in a week or two.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: EX8000 1.0.1.192 Firmware released
Check the host names on your devices, set a name if you can. Some devices don't support host names.
Let us know how it goes.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: EX8000 1.0.1.192 Firmware released
After sitting overnight, the EX8000 has the names for all the devices except a roku attached to the network router and an HP printer bridged to the router through an R7000 (i.e. r7000->R7000p->EX8000). Not terrible, the R7000p is the one that I really need identifying everything correctly and it does.
There are two anomalies: 1) I have a roku ultimate connected to the EX8000, it is on the 1733 5Ghz channel (161) and it shows a connection rate of 6Mbps even though the roku says it is getting 73Mbps download speed and 2) I have an R7000 bridged to the EX8000, it connects to channel 36 - the ex8000 reports a ghost MAC address one less than the MAC of the R7000 (R7000 ends in BC, ghost is same but ends in BB) connected at 6Mbps. Neither of these anomalies are functional issues.
Overall, I am pretty happy with the EX8000 as an access point.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: EX8000 1.0.1.192 Firmware released
Sounds like the host names need a little time to settle in to the EX.
Enjoy.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: EX8000 1.0.1.192 Firmware released
Hello nhinkle,
Thank you for your post. Our Engineering team is interested in working with you directly to help clarify the issues you reported. If you're interested, please send me a message with your contact info.
~Christian
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more