× NETGEAR would like to hear from you about specific features so we can improve your experience. To participate in this survey please click HERE.
Nighthawk Mesh WiFi

Welcome to the Nighthawk Mesh Community


Advanced Whole Home WiFi Click to Buy Nighthawk Mesh WiFi 6
Reply

Compatibility with AT&T UVerse

craholtz
Aspirant

Compatibility with AT&T UVerse

Is Nighthawk Dual Band Mesh WiFi 6 System - 2 pack (MK62) compatible with AT&T

Message 1 of 9
plemans
Guru

Re: Compatibility with AT&T UVerse

Yes. 

do you usually have to make changes with the att device to get it working properly? Yes. ATT tends to give people combo units which makes the network run a double nat without some changes to either the att router or the netgear router. 

Current setup: CM2000-> RBKE963B-> Trendnet TEG-S380-> GS716T-> pi-hole
also in AP setup: RAXE500->EAX80
1.4gig download/50mbps upload from Xfinity
We’re members of the public helping out on our own time.
Message 2 of 9
craholtz
Aspirant

Re: Compatibility with AT&T UVerse

Currently I don’t have a router, just a modem. I’m getting about 40-50 mbps download speed, which is the fastest speed available for my area. I was told that this router would help with all of the WiFi devices running in the house which is about 3,000 sq ft and is two-stories. I just want to make sure it will work with our AT&T U-Verse.
Message 3 of 9
plemans
Guru

Re: Compatibility with AT&T UVerse

again, most of att devices have an integrated router. Which device are you currently using? 

Current setup: CM2000-> RBKE963B-> Trendnet TEG-S380-> GS716T-> pi-hole
also in AP setup: RAXE500->EAX80
1.4gig download/50mbps upload from Xfinity
We’re members of the public helping out on our own time.
Message 4 of 9
craholtz
Aspirant

Re: Compatibility with AT&T UVerse

It’s from AT&T, a Pace model 5268AC
Message 5 of 9
plemans
Guru

Re: Compatibility with AT&T UVerse

Which has an integrated router. 

You'd need the pace put in "passthrough" mode to disable its routing functions. 

Or the orbi put in the Pace's DMZ. 

Or the orbi put in AP (access point) mode so only 1 router is in router mode. 

Current setup: CM2000-> RBKE963B-> Trendnet TEG-S380-> GS716T-> pi-hole
also in AP setup: RAXE500->EAX80
1.4gig download/50mbps upload from Xfinity
We’re members of the public helping out on our own time.
Message 6 of 9
craholtz
Aspirant

Re: Compatibility with AT&T UVerse

I’m not sure how to do any of those things
Message 7 of 9
plemans
Guru

Re: Compatibility with AT&T UVerse

If you're planning on setting it on the Pace, the best bet is to contact att. They can walk you through it. there's guides online as well like this:

https://www.att.com/support/smallbusiness/article/smb-internet/KM1188700/

 

if you plan on putting the netgear in access point mode then the guide for the device walks you through it. 

Current setup: CM2000-> RBKE963B-> Trendnet TEG-S380-> GS716T-> pi-hole
also in AP setup: RAXE500->EAX80
1.4gig download/50mbps upload from Xfinity
We’re members of the public helping out on our own time.
Message 8 of 9
craholtz
Aspirant

Re: Compatibility with AT&T UVerse

What’s the difference and what’s recommended?
Message 9 of 9
Top Contributors
Discussion stats
  • 8 replies
  • 3576 views
  • 0 kudos
  • 2 in conversation
Announcements

Orbi WiFi 6E