- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Re: RAX200 Firmware Version 1.0.2.88 breaks ipv6
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
RAX200 Firmware Version 1.0.2.88 breaks ipv6
Hello,
RAX200 Firmware Version 1.0.2.88. Breaks ipv6 ! Is this suppose to be?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RAX200 Firmware Version 1.0.2.88 breaks ipv6
Noticed the LAN ipv6 took, but not having ipv6 the way I normally see it configured. I downgraded back to previous firmware.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RAX200 Firmware Version 1.0.2.88 breaks ipv6
Hi RajaDaja,
Thanks for the feedback. Were you able to perform a factory reset after the firmware update?
Christian
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RAX200 Firmware Version 1.0.2.88 breaks ipv6
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RAX200 Firmware Version 1.0.2.88 breaks ipv6
I am having similar problems with the IPV6 disappearing after the latest firmware upgrade. The problem is that the updgrade includes many features that make my many IoT devices connect consistently to the router. My iPhoneXsMax connected to the router shows 2 IPV6 addresses, but my desktop and iPad do not. I also have an EAX80 hardwired to the router using CAT6 cabling as an AP for the upstairs - it also does not show an IPV6 address. The Xfinity . This is really frustrating that after spending $850 for these high end devices, all I get is a new problem. I installed the prior firmware on the routr, power cycled the cable modem several times (and between the set ups), reset the router and reconfigured things manually (not using a backup), and then upgraded, rest the router and updated things manually - I have spent way too many hours trying to get this high end equipment to function. PLEASE RELEASE A TESTED, FULLY FUNCTIONAL FIRMWARE UPDATE. PLEASE. I AM SO FRUSTRATED.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RAX200 Firmware Version 1.0.2.88 breaks ipv6
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RAX200 Firmware Version 1.0.2.88 breaks ipv6
Just wondering if any updates for this? Recently purchased an RAX200, and could not get it to pick up an IP from our business ISP.
Returned/Exchanged the router and no-go. Contacted support again and the answer is known issue, find another way to get internet access working or get a different router...not cool. So that's 2 being returned/sent back.
Anyone have any updates on a fix or firmware to use or other workaround?
Just as a sanity check, I also tried with firmware: https://kb.netgear.com/000062038/RAX200-Firmware-Version-1-0-2-92-Hot-Fix
But still cannot pick-up an IPv6 address. Put in our R8000P and a Linksys EA8300 and both are able to aquire IPv6 addresses, so it's not my ISP, definately this device/firmware.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RAX200 Firmware Version 1.0.2.88 breaks ipv6
Private message Christian_R
Provide the S/N with a brief summary of your ipv6 issue of your RAX200. He’s Netgear Mod. He will help you.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RAX200 Firmware Version 1.0.2.88 breaks ipv6
Ok thanks, will send him a PM him now w/ those details. Thanks.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RAX200 Firmware Version 1.0.2.88 breaks ipv6
@rinthos wrote:Ok thanks, will send him a PM him now w/ those details. Thanks.
While you're waiting,
From my experience, F/W V1.0.2.8_1.0.45 is the most stable with ipv6 functionality. Been on it for a while. Tried all the F/W available, even one from Netgear Mode, which by the way, work great for a while then the internet just froze while working. I panicked and did a quick F/W downgrade back to.........you guessed it.....V1.0.2.8_1.0.45. Been good ever since. I have Auto update disable. Good luck
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more