- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
CenturyLink Fiber RBR750 config
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Solved! Go to Solution.
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
@Seattle_RBR750 wrote:
Yes. This was my guide until my 4th failed attempt. I guess my questions based off this Reddit post are #1- how to “enable” gateway mode on the RBR750? #2- I was told by CenturyLink my PPP and PPoE credentials were identical? On my CL router admin pages I could only find PPP. Will that prevent a successful outcome? #3- is VLAN tag 201 the correct tag?
That Reddit article assumed that the reader was installing two separate pieces of equipment:
- One box to "talk to CenturyLink, and another to be
- The Customer's home router.
In such a situation, most people would not want to have "two routers" and would thus put the first device into a bridge or gateway mode. Your goal is to install only one device: the RBR750 router. So, the RBR750 should be left in the default router mode.
As for VLAN 201, the more I read, the more confusing it is. Netgear routers use VLAN to support internet television. (See page 74 of the user manual: https://www.downloads.netgear.com/files/GDC/RBK752/RBK752_UM_EN.pdf )
This video implies (in some of the comments) that when the customer router is not designed to put a VLAN tag on the WAN port, the customer can use a managed switch (such as a 5-port GS-105Ev2 - under $40 on Amazon) to add the VLAN tag on the WAN port. https://www.youtube.com/watch?v=xa76pRdQYGY
All Replies
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CenturyLink Fiber RBR750 config
Something to ask the ISP for help and information about to see if there HW is needed or not and for information on what configuration is needed on the RBR if there HW isn't needed.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CenturyLink Fiber RBR750 config
Is this the router CenturyLink provided?
https://www.centurylink.com/home/help/internet/modems-and-routers/greenwave-c4000.html
It appears that others have found solutions. Might follow this advice:
(That comment about using only Port 4 seemed a bit unusual.)
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CenturyLink Fiber RBR750 config
Thanks!
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CenturyLink Fiber RBR750 config
Place the CL gateway is pass-through mode if it doesn't have a bridge mode setting?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CenturyLink Fiber RBR750 config
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CenturyLink Fiber RBR750 config
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
@Seattle_RBR750 wrote:
Yes. This was my guide until my 4th failed attempt. I guess my questions based off this Reddit post are #1- how to “enable” gateway mode on the RBR750? #2- I was told by CenturyLink my PPP and PPoE credentials were identical? On my CL router admin pages I could only find PPP. Will that prevent a successful outcome? #3- is VLAN tag 201 the correct tag?
That Reddit article assumed that the reader was installing two separate pieces of equipment:
- One box to "talk to CenturyLink, and another to be
- The Customer's home router.
In such a situation, most people would not want to have "two routers" and would thus put the first device into a bridge or gateway mode. Your goal is to install only one device: the RBR750 router. So, the RBR750 should be left in the default router mode.
As for VLAN 201, the more I read, the more confusing it is. Netgear routers use VLAN to support internet television. (See page 74 of the user manual: https://www.downloads.netgear.com/files/GDC/RBK752/RBK752_UM_EN.pdf )
This video implies (in some of the comments) that when the customer router is not designed to put a VLAN tag on the WAN port, the customer can use a managed switch (such as a 5-port GS-105Ev2 - under $40 on Amazon) to add the VLAN tag on the WAN port. https://www.youtube.com/watch?v=xa76pRdQYGY
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CenturyLink Fiber RBR750 config
One last question: I did preemptively purchase a Netgear GS305EP switch based off another article I read. Now that I’ve setup ppoe and VLaN on the orbi router, what additional benefit can I gain from adding this switch? Probably a question for a new thread but I’d you have any quick answer and/or resources I will continue my novice journey. Thanks!
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CenturyLink Fiber RBR750 config
@Seattle_RBR750 wrote:
I did preemptively purchase a Netgear GS305EP switch based off another article I read. Now that I’ve setup ppoe and VLaN on the orbi router, what additional benefit can I gain from adding this switch?
People typically connect a switch to one of the LAN ports when there are more wired devices to connect then there are ports. This little switch would power four Power over Ethernet (PoE) devices, such as cameras. I purchased a similar PoE switch to avoid cluttering up my garage with individual PoE gizmos.
Aside from that, it makes a nice paperweight.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CenturyLink Fiber RBR750 config
I didn't expect this. I'm seeing reduced Download/Upload speeds after removing the CL hardware. I would have expected flat or even a slight increase. Any ideas how to boost them back to the old numbers? See attached screenshot for comparison.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CenturyLink Fiber RBR750 config
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CenturyLink Fiber RBR750 config
What speed results if you use a wired PC connected to the RBR and Ooklas installable speed test app?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CenturyLink Fiber RBR750 config
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CenturyLink Fiber RBR750 config
Orbi app tests thru the mobile devices wifi connection so results depends on capabilities of the mobile devices and wifi connection so results may differ. Recommend testing with a wired PC and Ooklas speed test app to get more accurate results.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CenturyLink Fiber RBR750 config
@FURRYe38 wrote:
Orbi app tests thru the mobile devices wifi connection so results depends on capabilities of the mobile devices and wifi connection so results may differ. Recommend testing with a wired PC and Ooklas speed test app to get more accurate results.
I am pretty confident that when the Orbi app reports a Speed Test, the actual test was performed on the Orbi router and the results communicated to the Orbi app for display. The Orbi app can report a Speed Test when connected to the router with Anywhere Access, i.e. when connected to any network "Anywhere" on the internet.
I just now performed a Speed Test using the Orbi app when my smartphone was connected to the internet using LTE. (no WiFi at all) and got the usual results.
I have found that Ookla Speed Test can vary tremendously from one minute to another.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CenturyLink Fiber RBR750 config
Orbi app can test via local network as well which maybe more accurate than Anywhere Access. AA could be effecting speed results. I always use Local Network when testing speeds using Orbi app.
Have never had any problems with Ooklas speed test app. Its way more reliable and accurate than the Orbi app is IMO. Find a accurate and reliable speed test server and favorite it. There can be many different speed test servers in ones local area. Some maybe less accurate or more busier than others.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CenturyLink Fiber RBR750 config
Perhaps there is a terminology issue. When my smartphone is disconnected from WiFi (LTE data only) and I open the Orbi app and select Speed Test, which device is performing the Speed Test?
- My smartphone, connected to LTE data?
- The Orbi router, which communicates the results through Anywhere Access to the Orbi app on my smartphone?
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more