×

Introducing the Orbi 970 Series Mesh System with WiFi 7(BE) technology. For more information visit the NETGEAR Press Room.

Orbi WiFi 7 RBE973
Reply

RBR50 poner IP FIJA a los dispositivos conectados.

EnriqueJ
Aspirant

RBR50 poner IP FIJA a los dispositivos conectados.

Hola buenas tardes. Necesito por favor instrucciones para poner IP fija a todos los dispositivos que conecte al Sistema RBR50, incluso al mismo Router.

Gracias

Model: RBR50|Orbi AC3000 Tri-band WiFi Router
Message 1 of 9

Accepted Solutions
FURRYe38
Guru

Re: RBR50 Put fixed IP in the router, in the satellite and in the devices that connect.

This would be a double NAT (two router) condition which isn't recommended. https://kb.netgear.com/30186/What-is-Double-NAT
https://kb.netgear.com/30187/How-to-fix-issues-with-Double-NAT
Couple of options,
1. Configure the modem for transparent bridge or modem only mode. Then use the Orbi router in router mode. You'll need to contact the ISP for help and information in regards to the modem being bridged correctly.
2. If you can't bridge the modem, disable ALL wifi radios on the modem, configure the modems DMZ/ExposedHost or IP Pass-Through for the IP address the Orbi router gets from the modem. Then you can use the Orbi router in Router mode.
3. Or disable all wifi radios on the modem and connect the Orbi router to the modem, configure AP mode on the Orbi router. https://kb.netgear.com/31218/How-do-I-configure-my-Orbi-router-to-act-as-an-access-point and https://www.youtube.com/watch?v=H7LOcJ8GdDo&app=desktop

View solution in original post

Message 9 of 9

All Replies
FURRYe38
Guru

Re: RBR50 poner IP FIJA a los dispositivos conectados.

In inglese per favore

Message 2 of 9
EnriqueJ
Aspirant

Re: RBR50 Put fixed IP in the router, in the satellite and in the devices that connect.

Please, I need instructions or explanation to put fixed or static IP, in the router, in the satellite and in the devices that connect to the RBR50.

This is my router.


Thank you

Model: RBR50|Orbi AC3000 Tri-band WiFi Router
Message 3 of 9
FURRYe38
Guru

Re: RBR50 Put fixed IP in the router, in the satellite and in the devices that connect.

Refer to page 73 of the user manual for setting "reserved" IP addresses ON the RBR for your devices. You can set a reserved IP address for the RBS as well:

https://www.downloads.netgear.com/files/GDC/RBK50/Orbi_UM_EN.pdf

 

Message 4 of 9
EnriqueJ
Aspirant

Re: RBR50 Put fixed IP in the router, in the satellite and in the devices that connect.

Thanks for your reply. In the manual it is indicated that the IPs start with 192.x.x.x., however I have them as 10.x.x.x.

Attached several images for you to check.

If I click add, it shows all the devices, and I select 1, it adds them to fixed IP, I imagine.

The images are in Spanish.

 

Message 5 of 9
EnriqueJ
Aspirant

Re: RBR50 Put fixed IP in the router, in the satellite and in the devices that connect.

 
Message 6 of 9
FURRYe38
Guru

Re: RBR50 Put fixed IP in the router, in the satellite and in the devices that connect.

If you have 10.something, then your RBR is configured for 10.0.1.1 or something like that. This only happens if your RBR detects a up stream router in front of the RBR that uses 192.168.1.1. The RbR changes to 10.something to avoid the conflict. 

 

Do you have another router infront of the RBR? 

What is the Mfr and model# of the Internet Service Providers modem/ONT the NG router is connected too?

Message 7 of 9
EnriqueJ
Aspirant

Re: RBR50 Put fixed IP in the router, in the satellite and in the devices that connect.

Yes I have the router from the Vodafone company.

Router CM DOCSIS 3.0 premium  Compal CG7486E

Message 8 of 9
FURRYe38
Guru

Re: RBR50 Put fixed IP in the router, in the satellite and in the devices that connect.

This would be a double NAT (two router) condition which isn't recommended. https://kb.netgear.com/30186/What-is-Double-NAT
https://kb.netgear.com/30187/How-to-fix-issues-with-Double-NAT
Couple of options,
1. Configure the modem for transparent bridge or modem only mode. Then use the Orbi router in router mode. You'll need to contact the ISP for help and information in regards to the modem being bridged correctly.
2. If you can't bridge the modem, disable ALL wifi radios on the modem, configure the modems DMZ/ExposedHost or IP Pass-Through for the IP address the Orbi router gets from the modem. Then you can use the Orbi router in Router mode.
3. Or disable all wifi radios on the modem and connect the Orbi router to the modem, configure AP mode on the Orbi router. https://kb.netgear.com/31218/How-do-I-configure-my-Orbi-router-to-act-as-an-access-point and https://www.youtube.com/watch?v=H7LOcJ8GdDo&app=desktop

Message 9 of 9
Top Contributors
Discussion stats
  • 8 replies
  • 853 views
  • 3 kudos
  • 2 in conversation
Announcements

Orbi WiFi 7