My devices that use an RBS20 satellite are very slow. The speeds are roughly 30-50mbps. Doesn't matter if it is a wifi connection to the satellite or a wired ethernet connection to the satellite. To test, I have a satellite 2 feet away from the modem/router. If I turn off the satellite and connect to wifi on the modem/router, I get 200+mbps. Why is the satellite so slow?

This seems to be a very common product wide problem with these netgear Orbi satalites. Netgear fails to resolve the issue after we've collectively spent thousands of dollars on this defective product line. Anyone thinking class action law suit? This should be seriously considered. Netgear refuses to take responsibitiy or priority in resolving this issue and refuses to refund a defective product. Time to gather the collective and take legal action.

Ok, after FINALLY getting my RBS20 to connect to the CBR40, Having my RBK50 online doesn't help so RBS kept getting confused. :smileyfrustrated: So seems to be a speed problem for sure with a wired PC connected behind the RBS20 thats connected to the CBR40:I did a wire test thru the CBR to be sure wired is ok: Connection rate is good and seems to be working: CBR40 is in a faux AP mode since I don't have it connected to my ISP cable line. DHCP server disabled and the CBR40 LAN port connected to my RBK50 network. Beamforming, MIMO, FR and WMM are enabled on the CBR. Manual Channel 11 and 48 as my RBK50 is on 1 and 36. I even turned down the power output of the RBR50 to lesson the interference. I would make contact with NG support and open a support ticket. This needs to be looked at.Blanca_O

Nope. I gave up on Netgear. Switched to TP-Link Deco and it is way better.

Hi kevincc and renanmarques I have sent you a message. Please check your inbox. Regards, Blanca Community Team

FYI, I was curious where the problem appeared. Seems to be on 2.2.1.210 as I reverted my CBR40 an RBS20 back to v210 today. Factory reset both CBR and RBS. Still same 50Mbps on the down with a wired PC connected to the back of the RBS20. I reverted back to v2.1.4.6 on the CBR40 and v2.1.4.16 on the RBS20. Powered OFF both units for 30 seconds then back ON. Look what the results were: Seems that something broke in FW after v2.1.4.xkevinccBlanca_O ChristineT

Slow ethernet and wifi satellite speeds

29 Replies

jt2oux
Tutor
May 01, 2021
This seems to be a very common product wide problem with these netgear Orbi satalites. Netgear fails to resolve the issue after we've collectively spent thousands of dollars on this defective product line. Anyone thinking class action law suit? This should be seriously considered.

Netgear refuses to take responsibitiy or priority in resolving this issue and refuses to refund a defective product. Time to gather the collective and take legal action.
FURRYe38
Guru
Dec 30, 2020
What Firmware version is currently loaded?
What is the Mfr and model# of the Internet Service Providers modem/ONT the NG router is connected too?

What device are you using to test the speed with?

What is the size of your home? Sq Ft?
What is the distance between the router and satellite(s)? 30 feet or more is recommended in between RBR and RBS to begin with depending upon building materials when wirelessly connected.

Try enabling Beamforming and MIMO(MIMO may or may not be needed) and WMM. Under Advanced Tab/Advanced Settings/Wireless Settings

Try disabling the following and see:
Armor, Circle, Daisy Chain, Fast Roaming, IPv6 and Set 20/40Mhz Coexistence to 40Mhz only. Set Short preamble instead of Long preamble modes. Save settings and reboot the router and satellite(s).

One User Experience/Configuration:
https://community.netgear.com/t5/Orbi/Most-Stable-Orbi-Configuration/m-p/1941087/highlight/true#M97026
- kevincc
  Guide
  Dec 30, 2020
  See below for my answers.
  
  What Firmware version is currently loaded?
  - Firmware on my RBS20 satellite was 2.5.1.16 when I tested earlier. I updated it to 2.6.1.38 and got the same result (50mbps).
  What is the Mfr and model# of the Internet Service Providers modem/ONT the NG router is connected too?
  - I'm using a Netgear CBR40 modem/router.
  
  What device are you using to test the speed with?
  - A Dell laptop connected via ethernet cable to the RBS20 satellite.
  
  What is the size of your home? Sq Ft?
  - Irrelevant. My satellite is 1 foot from my modem.
  What is the distance between the router and satellite(s)? 30 feet or more is recommended in between RBR and RBS to begin with depending upon building materials when wirelessly connected.
  - 1 foot
  
  Try enabling Beamforming and MIMO(MIMO may or may not be needed) and WMM. Under Advanced Tab/Advanced Settings/Wireless Settings
  - Beamforming and MIMO are both enabled.
  -
  Try disabling the following and see:
  Armor, Circle, Daisy Chain, Fast Roaming, IPv6 and Set 20/40Mhz Coexistence to 40Mhz only. Set Short preamble instead of Long preamble modes. Save settings and reboot the router and satellite(s).
  - Armor and Circle are disabled.
  - Daisy chain is disabled.
  - Fast Roamin is disabled.
  - IPv6 is disabled.
  - The only thing related to 20/40Mhz Coexistence is a setting for the 2.4Ghz wifi. It says "Enable 20/40 MHz Coexistence." Are you saying I should disable this? Not sure how it is relevant if it only applies to the 2.4Ghz wifi. My issue is with a direct, wired ethernet connection to the RBS20 satellite, which it should be using 5Ghz for the backhaul, correct?
  - FURRYe38
    Guru
    Dec 30, 2020
    30 feet or more is recommended in between RBR and RBS to begin with depending upon building materials when wirelessly connected. 1ft is way too close.
kevincc
Guide
Dec 30, 2020
I'll try again since there is no way to get actual support from Netgear. I have an RBS20 satellite about 1 foot away from my Orbi modem/router. I have a laptop plugged into an ethernet port on the RBS20. The download speed is 48Mbps. If I connect directly to the modem/router, the download speed is 240Mbps. Why is the wired connection to the RBS20 so slow? Anything I can try to improve this?

Forum Discussion

Slow ethernet and wifi satellite speeds