- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
orbilogin.com doesn't work after changing to AP mode
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
orbilogin.com doesn't work after changing to AP mode
I am using my Orbi in AP mode, and once I switch it over I can no longer reach the Orbi via orbilogin.com. Is this expected?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: orbilogin.com doesn't work after changing to AP mode
@ericmcgovern wrote:I am using my Orbi in AP mode, and once I switch it over I can no longer reach the Orbi via orbilogin.com. Is this expected?
can here , just make sure you restart everything so all your devices pick up an ip from the upstream router as the subnet will be different
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: orbilogin.com doesn't work after changing to AP mode
Thanks for the reply - restart all devices (computer, nest, etc.) or restart network gear? Gateway, Orbi, etc.?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: orbilogin.com doesn't work after changing to AP mode
restart the lot as it all needs to be reset to obtain the right ip range
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: orbilogin.com doesn't work after changing to AP mode
Can you access its GUI using its IP address? If you did not set a static IP on the AP then you might have to check its current IP from the main router's DHCP list. There were some cases that orbilogin.com does not pull up the GUI after setting up the router to AP mode, but sometimes I can still access it using orbilogin.com. Hence, I prefer using the IP address of the AP that I set on it.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: orbilogin.com doesn't work after changing to AP mode
Mines in AP mode and I can restart the Orbi without any restart of my Frontier router.
Always able to reach login page and login.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: orbilogin.com doesn't work after changing to AP mode
I have restartred everything and still no dice on getting to the page via orbilogin.com. I have to go into my modem/router from Comcast dig for the IP, and by manually using the IP I can get to it. Not a huge deal because I don't see myself ever really going to the interface, just odd that it doesn't work.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: orbilogin.com doesn't work after changing to AP mode
Let's just probably accept that " It may or may NOT work" when router is on AP mode :-).
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: orbilogin.com doesn't work after changing to AP mode
Mine does the same thing, but only if I am connected to the satellite. If connected to the base router I can access using orbilogin.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: orbilogin.com doesn't work after changing to AP mode
I have same issue too can only connect via IP when in A/P mode
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: orbilogin.com doesn't work after changing to AP mode
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more