NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
R8000 V1.0.5.88 released?
I have been having connectivity issues with my R8000 as of late (~2 weeks) and finally came looking today for solutions. To my great surprise (and skepticism) there is a new V1.0.5.88 firmware available as of today?!? My incredulity stems partly from the large version bump (1.0.4.88->1.0.5.88) when the release notes state that the release only "addresses security vulnerabilities". I can find no mention of which security vulnerabilities this addresses on the advisory page . Additionally, aren't security patches typically relegated to W in the X.Y.Z.W version ID? All this compounds when considering this device is EOL for some time now... At any rate, curious to hear any more about this mysterious release and to hear if anyone else has tried it out. Best, SR8000P vulnerabilities http_basic_auth, weak_password
AT&T give me the message below; is AT&T correct? If so, can the R8000P be fixed? Device R8000P Description There were 2 vulnerabilities found on your R8000P. The vulnerabilities are http_basic_auth, weak_password. These vulnerabilities may allow an attacker to damage your device.Router does not support https protocol R9000 Nighthawk
Some time after I purchased the R9000 router the https protocol stopped being supported and I may only access the admin interface via http Are there any suggestions to restore https access to the admin interface. I have been updating the f/w but I haven’t received any updates in the last 2 years thank youNighthawk R7000 openvpn Cannot load certificate file client.crt
Hello I have Nighthawk R7000 running firmware V1.0.11.136_10.2.120 and I was wanting to run a vpn. I followed the instructions about how to turn on the vpn service and installing openvpn. When I try to run openvpn I get this error in the log: 2023-11-10 14:19:55 us=703000 MANAGEMENT: Client disconnected 2023-11-10 14:19:55 us=703000 Cannot load certificate file client.crt 2023-11-10 14:19:55 us=703000 Exiting due to fatal error Now searching here I found that this was a previous issue that was fixed in version 1.0.9.30 but that was back in 2018. Is there any solution now for the latest firmware? thanksNighthawk X4S R7800 keeps factory reseting
When I restart my router or it restarts itself it factory resets itself, it started about 4 days ago. 2 days ago I download the last update for it and reupdated it when it reset itself, it seemed to have worked but about 10 minutes ago my internet went out and when it came back I saw it reset itself again. So I downloaded the firewere from a few updates ago and added it to my router to see if it will stop resetting itself. If anyone knows how to fix this problem please let me know because I'm getting tired of having to reapply all my setting, I tried to upload my saved settings file to it but it won't turn anything back onFactory Reset Old Router After New One Installed (Nighthawk X10 AD7200, Model R9000
I just installed the Nighthawk RAXE500 router. I still have my old router, a Nighthawk X10 AD7200, Model R9000. I want to "reset" the X10, but I will have to plug it in to do so. I did not reset it before installing the new one. I want to know if it is safe to just plug in the old router to reset it, or do I have to either unplug the current router and modem, make sure the phone and laptop are off, etc. before I plug it in to do the factory reset, or do I have to take it somewhere "out of range" to have it reset? It has a reset button on the back. Any comments would be appreciated. Thank you very much.Nighthawk X6S R8000P Guest Network won’t enable with password protection
I am setting up a Nighthawk R8000P and have my main networks broadcasting and when O go to enable my guest network, if I password enable it, the router sends an error below. If I just open a guest network without a password, it works great. Any kind of password encryption, the below error: “Configuration Error” Any ideas???