Firmware 2.2.1.210 and connection problems Skybell

I have the same issue with Skybell not connecting after the upgrade. I downgraded to the earlier version and after sometime it upgraded to the latest version. I again downgraded to the earlier firmware and have been on that since saturday night, and everything is working great for now.

I am hoping Netgear can resolve this issue for us.

Thanks

After a lot of test work, I have some additional information.

Immediately after the update to firmware 2.2.1.210, the Skybell is connected and works as it should. At the moment the connection between the Orbi router and the Skybell is interrupted for a moment, the Skybell will no longer be/come online.

Then I changed the password of my router and used only lower case (so no upper case letters or 'strange characters' like # @! etc) letters. The Skybell does not connect. Then I have changed my password into numbers only. This too has no result at all. Finally, I did not use a password and then the Skybell immediately connected to my Orbi.

So it looks like it is a password/security problem because the router no longer accepts the existing ‘Skybell password’.

Thanks for the detailed response, so nothing can be done for now till the fix is provided thru the next firmware release? We cannot remove the password as such.

So when not using any PW ON the router you turned OFF WPA security all together?

---

freakievinnie wrote:

After a lot of test work, I have some additional information.

Immediately after the update to firmware 2.2.1.210, the Skybell is connected and works as it should. At the moment the connection between the Orbi router and the Skybell is interrupted for a moment, the Skybell will no longer be/come online.

@Then I changed the password of my router and used only lower case (so no upper case letters or 'strange characters' like # @! etc) letters. The Skybell does not connect. Then I have changed my password into numbers only. This too has no result at all. Finally, I did not use a password and then the Skybell immediately connected to my Orbi.

So it looks like it is a password/security problem because the router no longer accepts the existing ‘Skybell password’.

---

---

FURRYe38 wrote:

So when not using any PW ON the router you turned OFF WPA security all together?

---

Yes, the Skybell connects immediately when I NOT using a password on the router (leave it blanc) and TURNED OFF (Security Options select 'None' ) WPA security. 

Ok, thank you for confirming this. I remember asking you about a few post prior. Also you said trying the other modes didn't work either. Something is broke in WPA/WPA2 and SkyBell. This is something to bring up with NG support.

ChristineT

AmitR

Christian_R

---

freakievinnie wrote:

---

FURRYe38 wrote:

So when not using any PW ON the router you turned OFF WPA security all together?

---

Yes, the Skybell connects immediately when I NOT using a password on the router (leave it blanc) and TURNED OFF (Security Options select 'None' ) WPA security. 

---

Hello All, 

If you're still having issues with Skybell and the latest Orbi FW, please send me a PM with your name, email, phone, and preferred contact time (including time zone). 

~Christian 

It worked!  SkyBell technical support just emailed me tonight with a fix that worked like a charm.  The Skybell HD immediately connected back to my Orbi wifi network.  See below:

Thank you for contacting SkyBell Technical Support.

Please follow the instructions below to get the SkyBell back online:

- Press your SkyBell button in and hold it for about a minute. The LED will flash (rapid green>red and green>blue>YELLOW).
- Once you see the LED flash YELLOW, please release the SkyBell button.
- Within a minute, your SkyBell will be flashing red and green.

Once it is flashing red and green, select 'Add a new SkyBell' in your app and follow the on-screen instructions to re-sync your device until after you have selected your network. When asked to input your password, please select the "Advanced" at the top.

When syncing, you will need to use the advanced options within the SkyBell Application and enter the information below.

It will ask for the following:

-Password: This will be your WiFi password
-Keep it at WPA2
-IP Address: (see gateway first) Use the first three numbers from your default gateway and 201 for your 4th number (e.g. if your gateway is 192.168.1.x, use 192.168.1.201)
-Subnet Mask: 255.255.255.0
-Gateway: Use the number that follows "Default Gateway/Router" for your router/extender that you are using to connect the device (e.g. 192.168.1.x or 10.0.0.x, etc)
-DNS: 8.8.8.8

Finnaly a soultion That worked for me  .. skybell back online after a long weekend of tinkering .and frustration..

thank you

Ray

Glad someone contacted Skybell to get more help and information on this. Glad this seems to be working for others as well. You should mark this post a resolved so other will see it and find this information.

Thanks for posting it.

Enjoy. :smileywink:

---

tcaprio wrote:

It worked!  SkyBell technical support just emailed me tonight with a fix that worked like a charm.  The Skybell HD immediately connected back to my Orbi wifi network.  See below:

 

Thank you for contacting SkyBell Technical Support.

Please follow the instructions below to get the SkyBell back online:

- Press your SkyBell button in and hold it for about a minute. The LED will flash (rapid green>red and green>blue>YELLOW).
- Once you see the LED flash YELLOW, please release the SkyBell button.
- Within a minute, your SkyBell will be flashing red and green.

Once it is flashing red and green, select 'Add a new SkyBell' in your app and follow the on-screen instructions to re-sync your device until after you have selected your network. When asked to input your password, please select the "Advanced" at the top.

When syncing, you will need to use the advanced options within the SkyBell Application and enter the information below.

It will ask for the following:

-Password: This will be your WiFi password
-Keep it at WPA2
-IP Address: (see gateway first) Use the first three numbers from your default gateway and 201 for your 4th number (e.g. if your gateway is 192.168.1.x, use 192.168.1.201)
-Subnet Mask: 255.255.255.0
-Gateway: Use the number that follows "Default Gateway/Router" for your router/extender that you are using to connect the device (e.g. 192.168.1.x or 10.0.0.x, etc)
-DNS: 8.8.8.8

---

Boom -- The solution above worked. Thanks for sharing!

Its the IP address in your case, use the ones i have listed below

It will ask for the following:

-Password: This will be your WiFi password
-Keep it at WPA2

-IP Address: (see gateway first) Use the first three numbers from your default gateway and 201 for your 4th number (e.g. if your gateway is 10)  Use - 10.0.0.201

-Subnet Mask: 255.0.0.0

-Gateway: Use the number that follows "Default Gateway/Router" for your router/extender that you are using to connect the device: Use - 10.0.0.1

-DNS: 8.8.8.8

Enjoy. :smileywink:

---

Luisfo wrote:
Finally worked!

Thanks a lot!!!

---

If your Default Gateway is 192.168.1.1 use subnet 255.255.255.0 and IP address 192.168.1.201

If your Default Gateway is 10.0.0.1 use subnet 255.0.0.0 and IP address 10.0.0.201

Hope that helps people

RBR20

Thank you, you saved me much heartache and frustration.  My SkyBell HD is working now.  

Enjoy. :smileywink:

---

deeperBrea wrote:

RBR20

Thank you, you saved me much heartache and frustration.  My SkyBell HD is working now.  

---

after upgradeing my firmware, my satellite (RBS50) won't connect. I tried almost everything on the web that doesn't seem to work .

I have the RBR50 Oribi .

ericsteward2003@ yahoo.com

EST

Worked all fine :) thank you for the tip.