Hello. Recently I wanted to open a dedicated server for csgo, which port is 27015. But it doesn't works, I tried to make a port test and this happened. Any solution? (That's weird because I have the port opened and uPnP unabled)

Works for me.Have you checked that 10.0.0.2 responds as expected on 27015 from the internal network?

Yep, I executed netstat -an and it doesn't appear 10.0.0.2:27015. Also, I did a port test on whatsmyip and it shows me this

SupahFox wrote: Yep, I executed netstat -an and it doesn't appear 10.0.0.2:27015. Is 10.0.0.2 the computer running the service or your router? If the latter, you need to forward it to the IP address of the computer where the required service is running instead.

Yup, 10.0.0.2 is the computer's internal IP adress

What Firmware is currently loaded?What is the Mfr and model# of the ISP modem the NG router is connected too? SupahFox wrote: Hello. Recently I wanted to open a dedicated server for csgo, which port is 27015. But it doesn't works, I tried to make a port test and this happened. Any solution? (That's weird because I have the port opened and uPnP unabled)

Port Forwarding not working | NETGEAR Communities

14 Replies

Mooose
Luminary
Apr 21, 2019
Works for me.

Have you checked that 10.0.0.2 responds as expected on 27015 from the internal network?
- SupahFox
  Tutor
  Apr 21, 2019
  Yep, I executed netstat -an and it doesn't appear 10.0.0.2:27015.
  
  Also, I did a port test on whatsmyip and it shows me this
  - Mooose
    Luminary
    Apr 21, 2019
    SupahFox wrote:
    
    Yep, I executed netstat -an and it doesn't appear 10.0.0.2:27015.
    
    Is 10.0.0.2 the computer running the service or your router? If the latter, you need to forward it to the IP address of the computer where the required service is running instead.
FURRYe38
Guru
Apr 22, 2019
What Firmware is currently loaded?
What is the Mfr and model# of the ISP modem the NG router is connected too?

SupahFox wrote:

Hello. Recently I wanted to open a dedicated server for csgo, which port is 27015. But it doesn't works, I tried to make a port test and this happened. Any solution? (That's weird because I have the port opened and uPnP unabled)
- SupahFox
  Tutor
  Apr 22, 2019
  The actual firmware is 2.3.1.48
  The modem is a ZTE zxhn f660 and yes, is connected to NG router
  - FURRYe38
    Guru
    Apr 22, 2019
    Modem Combo Units:
    This would be a double NAT condition which isn't recommended. https://kb.netgear.com/30186/What-is-Double-NAT
    Couple of options,
    1. Configure the modem for transparent bridge mode. Then use the Orbi router in router mode. You'll need to contact the ISP for help and information in regards to the modem being bridged correctly.
    2. If you can't bridge the modem, disable ALL wifi radios on the modem, configure the modems DMZ or IP Pass-Through for the IP address the Orbi router gets from the modem. Then you can use the Orbi router in Router mode.
    3. Or disable all wifi radios on the modem and connect the Orbi router to the modem, configure AP mode on the Orbi router. https://kb.netgear.com/31218/How-do-I-configure-my-Orbi-router-to-act-as-an-access-point and https://www.youtube.com/watch?v=H7LOcJ8GdDo&app=desktop

Forum Discussion

Port Forwarding not working