HiI have a problem with my 4GX Advanced III (Netgear AirCard 810S), when I push the power bottom it shows Telestar and 4XG and then go to black screen with "Shutting down" , it stay for long time please advice Thanks in advance

Was editing as you replied^ what does the screen say on mains only with no battery ? Still "shutting down" ? If the battery is caput/shorting it can send wrong readings to the OS. Can you connect it via usb to computer with no battery ?

The infamous Telstra/810 problem.Remove the battery (and charger) for 5 minutes. Try again with charger on only see if you can connect - then battery insert, you may end up in your usual cycle.Try with charger only (will run with no battery).This usually happens when the battery is far too low/firmware playing up (firmware will protect against strange battery voltage issues to protect a device from overheating).Best use a charger/cable with adequate voltage not any cable/usb plug, preferable the original lead/plug.You may try and charge for a few hours and see if that works or just jump ahead:With battery removed & on usb power only, connect to Wifi and go to Admin/192.168.1.1 (this may differ on Telstra, the logon details should be on your Aircard),login and look for the ‘reset’ to factory defaults.MiFI devices are mini computer devices, like Windows, iOS etc etc sometimes you just need to reset to default.

Dear AyeAyeAyeFirst of all I would like to thank you for your reply.I tried all what you mentioned above but still not opening, The screen of AC810S show battery charged 100% and it is asking me to remove the cablewith USB cable I can see the menu of AC 810S in my Laptop, I did the RESET many times but again it is not opening When I remove the battery, push the power bottom for long time and connect the USB cable, the screen shows Update but because there is no Internet it did not get the update.FirmwareFirmware Version: NTG9X40C_10.13.02.00Firmware Build Date: 2015/09/03Web App Version: AC810S-1TLAUS_03.03.102.13Bootloader Version: NTG9X40C_10.13.02.00Hardware Version: 1.0TRU-Install: PHS_TELSTRA_B4059DeviceModel: AirCard 810SAC810S Manager: http://m.homePRI Version: 1266601, 01.22Power State: OfflineCurrent temperature: 33°CCurrent voltage: 4307mVBattery charge level: 100%Battery status: NormalBattery temperature: 34WWAN InfoIP Address: 0.0.0.0IPv6 Address: Please advice

You shouldn’t need to push power on mains only with battery removed, I wonder if doing that is actually activating ‘update search’ ?? I recall aold MIFI of mine doing the same, power button on mains only is a forced update, that might apply to this Telstra model?.I would remove the battery & sim, plug in (don’t push power - I’d expect it to know the battery is not there) then see if it boots then to connect to Wi-fi and reset again.When resetting with a sim in there sometimes updates will happen or it will force search at least and the possible download takes priority (as a security measurement).Certainly remove bat & sim, mains only connect and see if you can reset from the menu.Maybe the battery is faulty? It could be saying 100% but the anomaly is that it isn’t, if the above doesn’t help borrow a battery or spend 20 bucks on eBay.I hated Telstra firmware/software, Big Pond modem firmware were even worse as a division of Telstra lol. Worked fine in Europe tho, better than Oz, go figure!!

Also just found this on a google, might help (it is T crowd support so maybe not, but more likely than any T (sales) shop could help, T Flagship Collins, Melbourne were a right incompetent lot!).https://crowdsupport.telstra.com.au/t5/mobile-broadband/telstra-advance-iii-issue-quot-shutting-down-quot/td-p/555435

4GX Advanced III (Netgear AirCard 810S) not opening

13 Replies

AyeAyeAye
Apprentice
Aug 19, 2021
The infamous Telstra/810 problem.

Remove the battery (and charger) for 5 minutes. Try again with charger on only see if you can connect - then battery insert, you may end up in your usual cycle.

Try with charger only (will run with no battery).

This usually happens when the battery is far too low/firmware playing up (firmware will protect against strange battery voltage issues to protect a device from overheating).

Best use a charger/cable with adequate voltage not any cable/usb plug, preferable the original lead/plug.

You may try and charge for a few hours and see if that works or just jump ahead:

With battery removed & on usb power only, connect to Wifi and go to Admin/192.168.1.1 (this may differ on Telstra, the logon details should be on your Aircard),login and look for the ‘reset’ to factory defaults.

MiFI devices are mini computer devices, like Windows, iOS etc etc sometimes you just need to reset to default.
- sinan60
  Aspirant
  Aug 19, 2021
  Dear AyeAyeAye
  First of all I would like to thank you for your reply.
  I tried all what you mentioned above but still not opening,
  The screen of AC810S show battery charged 100% and it is asking me to remove the cable
  with USB cable I can see the menu of AC 810S in my Laptop, I did the RESET many times but again it is not opening
  When I remove the battery, push the power bottom for long time and connect the USB cable, the screen shows Update but because there is no Internet it did not get the update.
  Firmware
  Firmware Version: NTG9X40C_10.13.02.00
  Firmware Build Date: 2015/09/03
  Web App Version: AC810S-1TLAUS_03.03.102.13
  Bootloader Version: NTG9X40C_10.13.02.00
  Hardware Version: 1.0
  TRU-Install: PHS_TELSTRA_B4059
  Device
  Model: AirCard 810S
  AC810S Manager: http://m.home
  PRI Version: 1266601, 01.22
  Power State: Offline
  Current temperature: 33°C
  Current voltage: 4307mV
  Battery charge level: 100%
  Battery status: Normal
  Battery temperature: 34
  WWAN Info
  
  IP Address: 0.0.0.0
  IPv6 Address:
  
  Please advice
  - AyeAyeAye
    Apprentice
    Aug 19, 2021
    You shouldn’t need to push power on mains only with battery removed, I wonder if doing that is actually activating ‘update search’ ?? I recall a
    old MIFI of mine doing the same, power button on mains only is a forced update, that might apply to this Telstra model?.
    
    I would remove the battery & sim, plug in (don’t push power - I’d expect it to know the battery is not there) then see if it boots then to connect to Wi-fi and reset again.
    
    When resetting with a sim in there sometimes updates will happen or it will force search at least and the possible download takes priority (as a security measurement).
    
    Certainly remove bat & sim, mains only connect and see if you can reset from the menu.
    
    Maybe the battery is faulty? It could be saying 100% but the anomaly is that it isn’t, if the above doesn’t help borrow a battery or spend 20 bucks on eBay.
    
    I hated Telstra firmware/software, Big Pond modem firmware were even worse as a division of Telstra lol. Worked fine in Europe tho, better than Oz, go figure!!

Forum Discussion

4GX Advanced III (Netgear AirCard 810S) not opening