RAXE500 firmware V1.0.10.86_2.0.40I am having trouble getting my IPv6 tunnel to work with my new RAXE500. the settings are all entered correctly, and when i use the 'ping -6 ipv6.google.com' command the command is able to retrieve the ipv6 address for ipv6.google.com, but both the server and client tunnel endpoints for the tunnel are timing out. I have even tried using anpth tunnel service, but the same issue occurs. test-ipv6.com gives the following results: Test with IPv4 DNS record ok (0.213s) using ipv4Test with IPv6 DNS record timeout (15.014s)Test with Dual Stack DNS record ok (0.615s) using ipv4Test for Dual Stack DNS and large packet ok (0.538s) using ipv4Test IPv6 large packet timeout (15.019s)Test if your ISP's DNS server uses IPv6 ok (0.564s) using ipv4Find IPv4 Service Provider ok (0.644s) using ipv4 ASN 14051Find IPv6 Service Provider timeout (15.011s) I am not sure how to proceed next or what trouble shooting to perform next all i know, is the ipv6 traffic is going into the router, but it does not seem to be leaving it. The tunnel used to work, but has not worked with the new router. AXE11000 WiFi Router (RAXE500)

Can you capture DEBUG logs, enable both debug and WAN to LAN captures before setting up the configuration, the after the configuration is setup, run your tests to check the configuration, then after save off the logs.

trying to access the router debug page (192.168.1.1/debug) results in a page from the router 404 Not FoundThe resource you have requested is not available.

ahh... ok. that was why it wasn't working then. I seem to have a bigger problem. I told the router to reboot using the interface, and it seemed to reboot, but it was immediately apparent that something had gone south. all my devices (PC, Android, Roku, Nintendo, etc.) were no longer able to reconnect to the network once it was back up. the devices (windows included) would connect but then drop the connection. I was connected for a few second long enough to discover that the router had stopped handing out ANY ipv4 setting at all. several power button cycles did not fix the issue. indeed, they seemed only exacerbate the problem. the router was no longer letting me log in, with windows and android there were authentication issues. I know for a fact that i was entering the right password each time. issue only seemed to get better once i disconnected the internet cable from the router and then did a power cycle. even then things did not immediately go back to normal. i had to wait 30 minutes and before the router finally let me logon to the network. after wards i plugged the internet cable back in, and the router picked up the settings passed by the modem. I am now able to get back into the network, and the admin pages. But I am most certainly NOT a happy camper at the moment. this is a brand new router, I expect it to at least function like it's supposed to for at least a little while.

here is the first set of debug files. hopefully they are the one you need. I will wait till i hear back to see if they are or not before i create the next set of logs using non configured router. oops... looks like the files won't upload to forum because they are much larger than the limit allows. I will upload them to my Onedrive and post the link

cybot

Luminary

Nov 11, 2022

IPv6 6to4 tunnel option broken? RAXE500

RAXE500 firmware V1.0.10.86_2.0.40

I am having trouble getting my IPv6 tunnel to work with my new RAXE500. the settings are all entered correctly, and when i use the 'ping -6 ipv6.google.com' command the command is able to retrieve the ipv6 address for ipv6.google.com, but both the server and client tunnel endpoints for the tunnel are timing out. I have even tried using anpth tunnel service, but the same issue occurs. test-ipv6.com gives the following results:

Test with IPv4 DNS record		ok (0.213s) using ipv4
Test with IPv6 DNS record		timeout (15.014s)
Test with Dual Stack DNS record		ok (0.615s) using ipv4
Test for Dual Stack DNS and large packet		ok (0.538s) using ipv4
Test IPv6 large packet		timeout (15.019s)
Test if your ISP's DNS server uses IPv6		ok (0.564s) using ipv4
Find IPv4 Service Provider		ok (0.644s) using ipv4 ASN 14051
Find IPv6 Service Provider		timeout (15.011s)

I am not sure how to proceed next or what trouble shooting to perform next all i know, is the ipv6 traffic is going into the router, but it does not seem to be leaving it. The tunnel used to work, but has not worked with the new router.

AXE11000 WiFi Router (RAXE500)

Forum Discussion

IPv6 6to4 tunnel option broken? RAXE500

20 Replies

404 Not Found