Hello, to whomI am having a problem with reloading the OS for my RND2000-200NAS. I had to replace both of my hard drives due to hard drive failure. I am following all of the steps to get it back online. Nothing is workingPRODUCT NUMBER: RND2000-200NASSERIAL NUMBER: 2UM221EB00188MAC 1 E0469AA09574MODEL NUMBER: RND-2B

Then you need to unformat the drives -- remove any partitions they contain -- or perform a factory default. Refer to page 27 of the hardware manual: ReadyNAS_Duov2_NV+v2_HW_en_23-Mar-12.pdf . The NAS uses it's own drive formatting, and the existing format is confusing it.

Try doing the factory default procedure on pages 16-17 of the manual here: https://www.downloads.netgear.com/files/GDC/RND2110/ReadyNAS_Duov2_NV+v2_HW_en_23-Mar-12.pdf

I said to unformat them because you replied that they were, in fact, already formatted, though you now seem to believe they are not. How did you "wipe them with Windows 10"? Windows itself will not typically "wipe" a drive with no partitions, though there are programs that run under it that can. So whether you created one or the drive was purchased with one already present, there may be a partition there. That is consistent with the error you are getting. But you don't seem to have even considered the second option, which StephenB has also suggested.

That Dashboard does not open in your browser has absolutely nothing to do with whether or not RAIDar works. Can you see the NAS in RAIDar and what status does it report? RAIDar also has nothing at all to do with an OS re-install using the reset button. The browser issue is related to TLS 1.0, and there are dozens of messages in the forum about work-arounds for that. But step one is getting your NAS to boot and install the OS to the new drives. Has that been accomplished? And FYI, neither StephenB nor I work for Netgear in any capacity. But we do know what does and does not work to resolve your problem, unless there is a hardware issue with the NAS.

It sounds like there may be an issue with the hard drives or the way they are being installed in the RND2000-2000NAS device. It would be best to check the documentation for the device to see if there are specific instructions for installing new hard drives, and to ensure that the hard drives are compatible with the device. If the hard drives are compatible and properly installed and you still unable to reload the OS, you may need to contact the manufacturer for further assistance.

RND2000-2000NAS unable to reload the OS after brand new hard drives

17 Replies

jennymartein
Aspirant
Jan 18, 2023
It sounds like there may be an issue with the hard drives or the way they are being installed in the RND2000-2000NAS device. It would be best to check the documentation for the device to see if there are specific instructions for installing new hard drives, and to ensure that the hard drives are compatible with the device. If the hard drives are compatible and properly installed and you still unable to reload the OS, you may need to contact the manufacturer for further assistance.
- bigwen12
  Aspirant
  Jan 18, 2023
  Thanks for this reply. All of that has been done. And I am waiting for a reply from support team.
  - Sandshark
    Sensei
    Jan 18, 2023
    This is a user-to-user forum, not official Netgear support.
    
    Are the drives in question formatted? If so, use a PC to remove all partitions and try again. You should not have to do anything special to install the OS to the new drives.
    
    Does RAIDar show the NAS at all and the drives as present, or "no disks"? Can you get into Dashboard at all? If it doesn't show the NAS at all, does it with no drives installed?
    
    Are you 100% sure your drives failed and not the NAS itself? Or maybe the power supply? Have you tested the new drives? It's unlikely you got two bad ones, but I suppose it could happen.

Forum Discussion

RND2000-2000NAS unable to reload the OS after brand new hard drives

17 Replies

Related Content

Admin Page keeps reloading

MR6110 Unable to connect

M5300 unaccessible after reload and/or uplink reboot

Unable to connect to AC750 extender

Unable to access NAS via WIN11 File Manager

NETGEAR Academy

ProSupport for Business