Forum Discussion
How to access disk information in Tech Support mode or Telnet, or get to a T3 support tech
I am having a disk problem with my ReadyNAS NV+ RND4000, I cannot get it to boot past "Kernel Panic" or "Bad Disk Found", and thus can't use the admin web interface to see what is going on. I am fai...
The best way to check your disk health is to power down the NAS and test the drives in a Windows PC using vendor tools (WDC's Lifeguard or Seagate's Seatools).
Another option is to try the RAIDar utility - it does report some disk status. https://kb.netgear.com/20684/ReadyNAS-Downloads
However, to answer your question:
I'm assuming an NV+ v1 here, but if your NAS says "NV+ v2" on the front panel, check the hardware manual for the v2 for booting into tech support mode.
You can boot up the v1 NAS in tech support mode using the instructions on pages 23-24 here: http://www.downloads.netgear.com/files/GDC/RND2110/Duov1_NV+v1_HW_en_06Dec11.pdf
Then you can telnet into the NAS. The login is root, the password is infr8ntdebug
Thanks Stephen.
I have a ReadyNAS NV+ and I did boot into Tech Support Mode, purchased a support incident, and (after a long wait) had a L3 tech tell me to replace disk #2. That did not solve the problem, it still reports "Bad Disk Found".
I have the latest version of RAIDar software but the NAS will not boot to the point of connecting to the network, unless it is in Tech Support mode, and then the RAIDar does not show any disk info - all 4 disks snow "not available" and grayed out.
I have a suspicion that it is not in fact a disk problem but rather something like a SATA controller card, because I have tried removing and replacing all the disks one by one and booting each time (with one disk removed or with a new disk in its place), and it is always the same behavior when booting. I'd just like to be able to determine exactly what the problem is.Also, even when booting into "Skip Volume Check" mode, it still displays "Bad Disk Found". This further makes me suspect that it is not a bad disk but some kind of controller or hardware problem.
I am able to use PuTTY to connect and login to the NAS when it is in Tech Support mode, but I don't know what to do once I am connected & logged in. Are there instructions published anywhere to find fault codes. logs, run tests, etc.?
I suppose my next step is to go get a USB enclosure or something and try to test each disk individually outside the NAS, so I can at least eliminate those as problems or find one if it is indeed bad. I am assuming this process will not destroy my RAID array - because if all the data is lost then this entire exercise is for nothing and I would just throw thew whole thing in the lake.
Thanks again for the help.As long as you only perform a read test, not a write test (which is the default for the vendor tools), your array will be untouuched. It is recommended you put the drives back in in the original order. And, of course, perform all removals and insertions with power off.
Your PC won't recognize the format of the drives, but that doesn't stop the vendor tools from doing their job.
It is kinda sounding like a motherboard or SATA backplane issue, but testing the drives is a good next step to finding out for sure. Since you don't have a USB dock and it does sound like you purchased a new drive, you could insert just that drive (or any unused drive) into the NAS and let it initialize. If it initializes, power off, move the drive to the next slot, power back on, and see if it boots. Repeat for all slots. If it boots in all slots, the NAS hardware is OK, If it boots in some, the NAS hardware is bad. If it boots in none, it's likely the NAS is bad, but you could be unlucky enough to get a new drive that's bad.
NETGEAR Academy
Boost your skills with the Netgear Academy - Get trained, certified and stay ahead with the latest Netgear technology!
Join Us!
