NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
FVS318N WAN to LAN low throughput
Hi, I'm struggling with WAN to LAN throughput on our FVS318N. It's a fibre to the cabinet PPPoE service rated at 76Mbps download and 19 Mbps upload. When initiating a PPPoE session direct into the back of the 'modem' we see 76M on a mulit-threaded download test, however plug the FVS318N in and this reduces to circa 55M, then plug in our GS108P and JGS524 and this drops to about 40M. We are running the latest firmware version 4.3.5-3. I have done a factory resest and just configured the FVS318N with the broadand settings with only one desktop client plugged in directly (no other switches or network components) and we still only get 55M. The FVS318N is rate at 250M WAN to LAN throughput so not sure what is going on here. Any help appreciated. Thanks.NetGear FVS 318N WAN throughput limited
I have read the other posts and also performed the recommended actions, but I am also experiencing limited throughput on my firewall. I recently upgraded my TWC to Spectrum Internet. The service connection went from 30Gb/s to 100Gb/sec. I also have a Netgear N450 Gateway & I connected my system directly to it (at 1Gb/sec) to test the connection speed via speedtest.net. I was able to get 95+Gb/sec download and 12+Gb/sec upload speeds. My 318N firewall is also WAN connected to the N450 Gateway at 1Gb/sec bandwidth. When I connect my system to the 318N firewall at 1Gb/sec and run speedtest.net, I am only able to achieve 42Gb/sec - 45Gb/sec download and 10Gb/sec - 11Gb/sec upload speeds. I have the latest software version loaded (v4.3.4-2). I have reset both devices and my system. I have turned the wireless on and off on the 318N, and performed the recommended tests without any increase in speed from my firewall. I am not using any encryption or VPN settings. I am definitely able to get the 100Mb/sec speed from my ISP throught the N450 Gateway. But the FVS318N is limiting the available performance.FVS318N Box-to-Box VPN with NAT
I'm trying to set up a box-to-box IPSec VPN tunnel between an office and branch location. The office location has an external static IP address so no problems there. However, the ISP servicing the branch provides a 192.168.X.X address to the FVS318N rather than an external (static or dynamic) IP address. The branch is effectively behind a virtual NAT device at the ISP. How can I set up a box-to-box VPN in this situation? Thanks for any assistance with this!FVS318N Radio Channel manual config causes unexpected behaviour
On my FVS318N I have configured the wireless channel to use Channel 6 (2437 Mhz) as a manual setting. However, the Current channel reported by the GUI is Channel 3 (2422 MHz) Any effort in making a manual channel configuration persist fails completely. I need a fixed channel setting as another wireless bridge has been configured to extend the network to a wired section. Firmware Version: 4.3.3-6 (Latest) below is part of the config file related to the Radio. Is this a bug in the fimware? dot11Radio = {} dot11Radio[1] = {} dot11Radio[1]["path"] = "1" dot11Radio[1]["dothMarkDfs"] = "0" dot11Radio[1]["beaconInterval"] = "100" dot11Radio[1]["txRate"] = "0" dot11Radio[1]["opMode"] = "ng40+" dot11Radio[1]["rtsCtsProtect"] = "1" dot11Radio[1]["radioenabled"] = "1" dot11Radio[1]["rtsThreshold"] = "2346" dot11Radio[1]["dothEnabled"] = "1" dot11Radio[1]["uapsd"] = "0" dot11Radio[1]["txPower"] = "20" dot11Radio[1]["cardNo"] = "1" dot11Radio[1]["rogueAPEnabled"] = "0" dot11Radio[1]["longRetry"] = "16" dot11Radio[1]["dtimInterval"] = "2" dot11Radio[1]["configuredChannel"] = "6" dot11Radio[1]["interfaceName"] = "wifi0" dot11Radio[1]["shortRetry"] = "16" dot11Radio[1]["radioNo"] = "1" dot11Radio[1]["band"] = "b" dot11Radio[1]["xmlId"] = "1" dot11Radio[1]["currentChannel"] = "2412" dot11Radio[1]["preambleMode"] = "Long" dot11Radio[1]["dothMaxPower"] = "30" dot11Radio[1]["fragThreshold"] = "2346" dot11Radio[1]["_ROWID_"] = "1" dot11Radio[1]["rxDiversity"] = "0" Appreciate your help and insightsNeed to Route ISP addresses to Internal IP
I have 2 domain names that are attached to specific IP addresses like normal, one is for mail and the other is for our internal website. I need to route thos static IP addresses directly to an internal IP address for our windows SBS 2011 exchange and web site. I opened the required ports but I seem to be missing where I can route the rest. The appliance is on another IP address and works fine for internet from our intranet. Thanks