NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
Orbi RBR50 Hourly Disconnect
Hello! I just want to start off the post by saying I have zero to no experience with a lot of this so please bare with me and forgive me if I say anything strangely.
So I recently switched to AT&T as my ISP. I already had the Orbi from my previous setup and am using with the router we got from AT&T. Initially, I had the Orbi set to router mode but I was unable to access many websites, etc. I read up on how to solve the issue and so I switched my Orbi to AP mode but ever since, I have been experiencing a "No internet connection" on all devices every hour. This occurs at about the same time and for approximately five minutes. I work at home and it's been giving me a really hard time. Any and all help will be greatly appreciated!
So I recently switched to AT&T as my ISP. I already had the Orbi from my previous setup and am using with the router we got from AT&T. Initially, I had the Orbi set to router mode but I was unable to access many websites, etc. I read up on how to solve the issue and so I switched my Orbi to AP mode but ever since, I have been experiencing a "No internet connection" on all devices every hour. This occurs at about the same time and for approximately five minutes. I work at home and it's been giving me a really hard time. Any and all help will be greatly appreciated!
11 Replies
What Firmware version is currently loaded?
What is the Mfr and model# of the ISP modem/ONT the NG router is connected too?What is the size of your home? Sq Ft?
What is the distance between the router and satellite(s)? 30 feet is recommended in between RBR and RBS to begin with depending upon building materials when wirelessly connected. https://kb.netgear.com/000036466/How-far-should-I-place-my-Orbi-satellite-from-my-Orbi-routerWhat channels are you using? Auto? Try setting manual channel 1, 6 or 11 on 2.4Ghz and any unused channel on 5Ghz.
Any Wifi Neighbors near by? If so, how many?Try enabling Beamforming and MIMO(MIMO may or maynot be needed) and WMM. Under Advanced Tab/Advanced Settings/Wireless Settings
Try disabling the following and see:
Armor, Circle, Daisy Chain, Fast Roaming, IPv6 and Set 20/40Mhz Coexistence to 40Mhz only. Set Short preamble instead of Long preamble modes. Save settings and reboot the router and satellite(s).Has a factory reset and setup from scratch been performed since last FW update?
Hello, i have exactly the same issue. For weeks now. Since Corona i am working fulltime at home, constantly connected via VPN.
Every hour at exact the same time all my connections got reset.
I loose my vpn connection and internet connection
On all my devices by the way.
My setup
RBR50 firmware V2.5.1.8
RBS50 x2 firmware V2.5.1.8
RBS50Y firmware V2.3.5.32
I am connected to the RBR50 via ethernet, which is wired via UTP6 to my cable modem.
If i connect to the internet directly i have no disconnects.
My VPN is a Cisco Anyconnect 4.3.03086
My house is about 310 sq meters (3300 sq ft), distance varies from 12m to 6m, depending on the walls (thick brick walls, al ot of concrete and piping).
Connections between them are good. Daisy chaining enabled (RBS50Y connects via one RBS50), roaming is working fine for other devices.
Fixed 2.4 channel, there are 2 or 3 other signals but not that strong.
Beamforming and MIMO and WMM enabled. Under Advanced Tab/Advanced Settings/Wireless Settings
Disabled: Armor, Circle
Set 20/40Mhz Coexistence to 40Mhz only.
Had a factory reset and setup from scratch since last FW update
This should not be happening to a system that has cost me about 700$
I am no n00b.
Tried changing DHCP lease time via the debug page, but all my clients have reserved IP's, but no change in the disconnects
What is the Mfr and model# of the ISP modem/ONT the NG router is connected too?
Do both wired and wireless get disconnected?
Only VPN?
30 feet is recommended in between RBR and RBS to begin with depending upon building materials when wirelessly connected. https://kb.netgear.com/000036466/How-far-should-I-place-my-Orbi-satellite-from-my-Orbi-router
What channels are you using? Auto? Try setting manual channel 1, 6 or 11 on 2.4Ghz and any unused channel on 5Ghz.
You can try to update your system to v16.
Update using this process:
wimmme wrote:Hello, i have exactly the same issue. For weeks now. Since Corona i am working fulltime at home, constantly connected via VPN.
Every hour at exact the same time all my connections got reset.
I loose my vpn connection and internet connection
On all my devices by the way.
My setup
RBR50 firmware V2.5.1.8
RBS50 x2 firmware V2.5.1.8
RBS50Y firmware V2.3.5.32
I am connected to the RBR50 via ethernet, which is wired via UTP6 to my cable modem.
If i connect to the internet directly i have no disconnects.
My VPN is a Cisco Anyconnect 4.3.03086
My house is about 310 sq meters (3300 sq ft), distance varies from 12m to 6m, depending on the walls (thick brick walls, al ot of concrete and piping).
Connections between them are good. Daisy chaining enabled (RBS50Y connects via one RBS50), roaming is working fine for other devices.
Fixed 2.4 channel, there are 2 or 3 other signals but not that strong.
Beamforming and MIMO and WMM enabled. Under Advanced Tab/Advanced Settings/Wireless Settings
Disabled: Armor, Circle
Set 20/40Mhz Coexistence to 40Mhz only.
Had a factory reset and setup from scratch since last FW update
This should not be happening to a system that has cost me about 700$
I am no n00b.
Tried changing DHCP lease time via the debug page, but all my clients have reserved IP's, but no change in the disconnects
The modem is a Motorola / CV6181E (DOCSIS).
Disconnects are both wired, wireless, and so the VPN also .
2.4GHz is on channel 1
5GHz is on channel 36
Changed them all, to no avail; but some interference should NOT cause network disconnects, certainly not on the laptop i am using wired tot the RBR50.
I will try to update to that new version 2.5.1.16 this evening.
Factory resetting and reconfiguring is a real PITA, since I have 50+ devices on my network, all with fixed IP's.
But i will and report back
Tnx for the feedback guys
