NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
Solved
cm1200 upstream randomly will start blinking intermittently and lose internet
Spectrum says its not on there end to check with Netgear. here is my event log though.
| Sat Oct 21 15:45:15 2023 | Notice (6) | CM-STATUS message sent. Event Type Code: 5; Chan ID: 33; DSID: N/A; MAC Addr: N/A; OFDM/OFDMA Profile ID: N/A.;CM-MAC=80:cc:9c:b2:2b:70;CMTS-MAC=00:17:10:88:a4:9f;CM-QOS=1.1;CM-VER=3.1; |
| Sat Oct 21 15:41:33 2023 | Warning (5) | REG-RSP-MP Mismatch Between Calculated Value for P1.6hi Compared to CCAP Provided Value;CM-MAC=80:cc:9c:b2:2b:70;CMTS-MAC=00:17:10:88:a4:9f;CM-QOS=1.1;CM-VER=3.1; |
| Sat Oct 21 15:41:28 2023 | Notice (6) | DS profile assignment change. DS Chan ID: 32; Previous Profile: ; New Profile: 1 2.;CM-MAC=80:cc:9c:b2:2b:70;CMTS-MAC=00:17:10:88:a4:9f;CM-QOS=1.1;CM-VER=3.1; |
| Sat Oct 21 15:41:23 2023 | Notice (6) | TLV-11 - unrecognized OID;CM-MAC=80:cc:9c:b2:2b:70;CMTS-MAC=00:17:10:88:a4:9f;CM-QOS=1.1;CM-VER=3.1; |
| Sat Oct 21 15:41:23 2023 | Error (4) | Missing BP Configuration Setting TLV Type: 17.9;CM-MAC=80:cc:9c:b2:2b:70;CMTS-MAC=00:17:10:88:a4:9f;CM-QOS=1.1;CM-VER=3.1; |
| Sat Oct 21 15:41:23 2023 | Error (4) | Missing BP Configuration Setting TLV Type: 17.8;CM-MAC=80:cc:9c:b2:2b:70;CMTS-MAC=00:17:10:88:a4:9f;CM-QOS=1.1;CM-VER=3.1; |
| Time Not Established | Notice (6) | Overriding MDD IP initialization parameters; IP provisioning mode = IPv6 |
| Time Not Established | Critical (3) | SYNC Timing Synchronization failure - Failed to acquire QAM/QPSK symbol timing;;CM-MAC=80:cc:9c:b2:2b:70;CMTS-MAC=00:00:00:00:00:00;CM-QOS=1.1;CM-VER=3.1; |
Power levels are with in spec:
https://kb.netgear.com/24311/Power-level-guidelines-for-a-NETGEAR-cable-modem-router
However you have a ton of Correctables and Un-correctables that should be most zeros
Have the ISP check the signal and line quality UP to the modem. Be sure the ISP provisions the modem correctly.
Be sure there are no coax cable line splitters in the between the modem and ISP service box.
Be sure your using good quality RG6 coax cable up to the modem.
Start with removing any amplifiers, signal attenuators, or splitters from the coax.
From there check the line for kinks, damage, moisture in the line.
Check the connectors for improperly made ends, foil touching the copper coax line, loose connections, bad/old/cheap connectors, or corroded connections. Replace them if you do.
Be sure to power OFF the modem for 1 minute then back ON.
https://community.netgear.com/t5/Cable-Modems-Routers/General-info-and-Troubleshooting-for-Cable-Modems/m-p/1530376#M12853
https://www.duckware.com/tech/solving-intermittent-cable-modem-issues.htmlBe sure your using a good quality LAN cable between the modem and router. CAT6 is recommended.
Any Criticals, Errors or Warnings seen in the event logs needs to be reviewed and resolved by the ISP. Indicates a signal issue on the ISP line up to the modem.
3 Replies
Replies have been turned off for this discussion
Please post a copy and paste of the modems connection status page.
https://kb.netgear.com/30007/How-do-I-obtain-the-cable-connection-information-from-a-NETGEAR-cable-modem-modem-router
Any Criticals, Errors or Warnings seen in the event logs needs to be reviewed and resolved by the ISP. Indicates a signal issue on the ISP line up to the modem.
Be sure your using a good quality LAN cable between the modem and router. CAT6 is recommended.
What is the brand and model of the host wifi router connected to the modem?added 3 screenshots of cable modem status.
Power levels are with in spec:
https://kb.netgear.com/24311/Power-level-guidelines-for-a-NETGEAR-cable-modem-router
However you have a ton of Correctables and Un-correctables that should be most zeros
Have the ISP check the signal and line quality UP to the modem. Be sure the ISP provisions the modem correctly.
Be sure there are no coax cable line splitters in the between the modem and ISP service box.
Be sure your using good quality RG6 coax cable up to the modem.
Start with removing any amplifiers, signal attenuators, or splitters from the coax.
From there check the line for kinks, damage, moisture in the line.
Check the connectors for improperly made ends, foil touching the copper coax line, loose connections, bad/old/cheap connectors, or corroded connections. Replace them if you do.
Be sure to power OFF the modem for 1 minute then back ON.
https://community.netgear.com/t5/Cable-Modems-Routers/General-info-and-Troubleshooting-for-Cable-Modems/m-p/1530376#M12853
https://www.duckware.com/tech/solving-intermittent-cable-modem-issues.htmlBe sure your using a good quality LAN cable between the modem and router. CAT6 is recommended.
Any Criticals, Errors or Warnings seen in the event logs needs to be reviewed and resolved by the ISP. Indicates a signal issue on the ISP line up to the modem.