Hello!I have a ReadyNAS Duo V2 and I haven't entered the setup for a long time.The system is Windows 10 and the problem happens in all browsersIt is working and I have access to the files.Now I need to enter the setup and I can't because the browsers don't accept the communication protocol.NASnumberIP/adminAn error occurred during a connection to 192.168.1.208. The remote system uses an unsupported version of the security protocol.Error code: SSL_ERROR_UNSUPPORTED_VERSIONThis site may not support the TLS 1.2 protocol, the minimum version supported by Firefox.Only the IP numberNASnumberIP/sharesincomplete sharing, only access to password changeMaybe updating the firmware will do it, but I can't install it without accessing the setup

WellingtonBDS wrote: I have a ReadyNAS Duo V2 Your screenshot appears to be from the original Duo (called a v1 here). The original Duo (v1) runs 4.1.x firmware says "ReadyNAS Duo" on the front panel. The Duo v2 runs 5.3.x firmware says "ReadyNAS Duo v2" on the front panel. Ignore other labels, they are more confusing than helpful. WellingtonBDS wrote: An error occurred during a connection to 192.168.1.208. The remote system uses an unsupported version of the security protocol. Error code: SSL_ERROR_UNSUPPORTED_VERSIONThis site may not support the TLS 1.2 protocol, the minimum version supported by Firefox. See this thread: https://community.netgear.com/t5/New-ReadyNAS-Users-General/Workaround-for-ERR-SSL-VERSION-OR-CIPHER-MISMATCH-problem-for/m-p/2198243 If you skip to the end, you'll find a setting which allows FireFox to connect. One downside of doing that is that it enable TLS 1.0 generally (for all websites). If you run Windows, then Internet Explorer or Edge in IE mode will also work. Editing virtual.conf (once you regain temporary access) is another option, instructions for that in the beginning of the thread. The Duo v2 add-on won't work in your case (since you actually have a v1). WellingtonBDS wrote: Only the IP numberNASnumberIP/sharesincomplete sharing, only access to password change That only shows you something if you have configured one or more shares to allow HTTP access.

WellingtonBDS wrote: I downloaded SSL EnableRootSSH_1.0.bin, but I don't know how to use it to access the root from the NAS You install it as an add-on in Frontview. Then you can access the NAS by entering ssh root@nas-ip-address from the windows search bar. That will open a command box. You will need to allow the connection the first time. Then enter the NAS admin IP password at the prompt.

WellingtonBDS wrote: Wouldn't it be for local access, where I put the .bin file in the NAS shared folder on my PC? You are looking at the wrong screen. Ready Remote hasn't worked for a very long time. You want to open up Status and then Add-ons in the left pane menu, and then choose "add new" from the top.

You started by clicking on "system", and you should have clicked on "status". Though it's possible that 4.2.x systems have a slightly different organization. I'll fire up my old NV+ and take a look.

StephenB wrote: Though it's possible that 4.2.x systems have a slightly different organization. I'll fire up my old NV+ and take a look. Yes, it is a bit different. Don't attempt to register or check for updates on the remote tab, as that will give you the "error connecting to remote server" error. If you do get it, then just click ok. Select System Update From the left pane. Then select Local at the top. First you "Choose File", and select the .bin file Next you click on "Upload and verify image".

Ready NAS duo V2 does not access frontview

20 Replies

StephenB
Guru
Mar 06, 2023
WellingtonBDS wrote:
I have a ReadyNAS Duo V2

Your screenshot appears to be from the original Duo (called a v1 here).

The original Duo (v1)

runs 4.1.x firmware

says "ReadyNAS Duo" on the front panel.

The Duo v2

runs 5.3.x firmware

says "ReadyNAS Duo v2" on the front panel.

Ignore other labels, they are more confusing than helpful.

WellingtonBDS wrote:

An error occurred during a connection to 192.168.1.208. The remote system uses an unsupported version of the security protocol.

Error code: SSL_ERROR_UNSUPPORTED_VERSION
This site may not support the TLS 1.2 protocol, the minimum version supported by Firefox.

See this thread:

https://community.netgear.com/t5/New-ReadyNAS-Users-General/Workaround-for-ERR-SSL-VERSION-OR-CIPHER-MISMATCH-problem-for/m-p/2198243

If you skip to the end, you'll find a setting which allows FireFox to connect. One downside of doing that is that it enable TLS 1.0 generally (for all websites). If you run Windows, then Internet Explorer or Edge in IE mode will also work.

Editing virtual.conf (once you regain temporary access) is another option, instructions for that in the beginning of the thread.

The Duo v2 add-on won't work in your case (since you actually have a v1).

WellingtonBDS wrote:

Only the IP number
NASnumberIP/shares
incomplete sharing, only access to password change

That only shows you something if you have configured one or more shares to allow HTTP access.
- WellingtonBDS
  Aspirant
  Mar 07, 2023
  Thank you for the informations
  I read your post (2022-03-05 03:50 AM) detailing the procedure, I copied the script in notepad++ and saved it in a shared folder on the NAS, I downloaded SSL EnableRootSSH_1.0.bin, but I don't know how to use it to access the root from the NAS
  - WellingtonBDS
    Aspirant
    Mar 07, 2023
    I installed FireFox 94.0.2 and now access the NAS frontview
    Hostname: nas-6B-AC-B6
    Model: ReadyNAS Duo [X-RAID]
    Serial: 24M4147V00C80
    Firmware: RAIDiator 4.1.16 [1.00a043]
    Memory: 256 MB [2.5-3-3-7]
    IPv4 address:: 192.168.1.208
    Volume C: Online, X-RAID, 2 disks, 79% of 1846 GB used