NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
Netword Performance issuse
Need some guidance on a Networking issues that started a few days ago and I am not sure how to how to troubleshoot. Problem - Every two minutes or so I lose the ability to access the internet, we...
Are you forwarding ports to the NAS in the router?
i am curious the bond0 and and tun10 interfaces.. are they supposed to be there?
NasOne:~# ifconfig -a
bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
eth0 Link encap:Ethernet HWaddr 00:1F:33:EA:50:95
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:16 Memory:ff6fc000-0
eth1 Link encap:Ethernet HWaddr 00:1F:33:EA:50:94
inet addr:192.168.101.3 Bcast:192.168.101.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:14079467 errors:0 dropped:7 overruns:0 frame:0
TX packets:2106931720 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:3083618709 (2.8 GiB) TX bytes:2046929944846 (1.8 TiB)
Interrupt:17 Memory:ff7fc000-0
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:26411 errors:0 dropped:0 overruns:0 frame:0
TX packets:26411 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1811103 (1.7 MiB) TX bytes:1811103 (1.7 MiB)
tunl0 Link encap:IPIP Tunnel HWaddr
UP RUNNING NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
I see both interfaces on my pro (though in my case I use bond0). I am wondering if tun10 is set up for remote.
What add ons do you have installed?
No add-ons install on the NAS.
to be on the safe side, I just turned off
Discovorry Services
ReadyDLNA
AFT protcol
FTP Protocol
The only services running are CIFS, HTTP, HTTPS
If you have a scratch disk, you could remove the pro disks (labeling them by slot), and install the install disk.
Then see if the clean factory install has the same problem.
NETGEAR Academy
Boost your skills with the Netgear Academy - Get trained, certified and stay ahead with the latest Netgear technology!
Join Us!
