NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
Solved
ReadyNas NV+ V1 Unable to communicate via Raidar/Frontview
Several weeks ago my NV+ V1 began to drop off my network, finally disapearing completely. When I reboot the unit all four drive lights are lit green, the power button stays lit, the eithernet port li...
Thanks Jenn. I will do as you have suggested and get back with the support people.
Rick
rcoop wrote:
No, can you elaborate?
ssh gives you a command line interface into the box, where'd you'd run linux shell commands. You can telnet into the v1 in tech support mode, and also run shell commands. If you were reasonably accomplished with linux, you could check some things (OS fullness, drive SMART stats, ...) and maybe fix the issue.
But you are unfamiliar with it, and tech support mode wouldn't be an easy place to learn.
My guess would be a filling OS partition. Do you have a backup? If so, its probably fastest to do a factory reset, and rebuild the NAS.
Another thing you could try (if you have a scratch disk) is to power down, remove the current disks (label by slot), and try installing just on the scratch - and see if it has the same problem.
Yes, I am unfamiliar with that. Way outside of my wheelhouse.
Did you mean an OS partion has failed? Yes I have a backup. However there are some more recent files that were not backed up, so I might do that as a last resort.
If I install a scratch disk and I still have the same problem, what does that tell me? And if not, would that mean a problem with my original disks? Can I use any old disk? And I won't loose the data if I reinstall the original disks?
I originally thought that my problem was of a hardware nature. Either the power supply or a network board within the NAS.
Thanks for your help.
rcoop wrote:
Did you mean an OS partion has failed?
Not failed exactly. Just full. It's only 2 GB on your NAS. That's just one possibility, it could be something else.
rcoop wrote:
If I install a scratch disk and I still have the same problem, what does that tell me? And if not, would that mean a problem with my original disks? Can I use any old disk? And I won't loose the data if I reinstall the original disks?
If you have the same problem with the scratch, then that tells you that the problem is with the NAS hardware. You can use a disk that isn't on the HCL for this. You aren't setting up a RAID array, just installing to one drive.
As long as you power down before you remove (or reinsert) the original drives, you won't lose any data.
While the disks are out, you could test them with vendor diags in a windows PC (seatools for seagate, lifeguard for western digital).
rcoop wrote:
I originally thought that my problem was of a hardware nature. Either the power supply or a network board within the NAS.
Both are possible, but since it failed on the upgrade, I am thinking a full OS partition is more likely.
If you upgraded the memory, then that could also be the issue - there are reports here that suggest the current firmware is more picky about memory than the older firmware was.
If it is hardware, you could try to find a used NV+ v1 chassis. You might also check your purchase date. Warranty is 5 years on the NV+ v1, so you might still be covered.
Netgear does offer per-incident support (if you are the original purchaser) so you could also contact them at support.netgear.com.
Is what you refer to as the OS called Raidiator? And how would the OS partition become full?
I will try the scratch disk route.
I've never upgraded the memory. Yes, I've thought of looking for another chassis, but my understanding of that is I will lose all of my data when I reinstall the existing drives in the new chassis.
Regarding the warranty, my unit was 5 yrs. old on October 12, 2015. I've been trying to contact NetGear for two weeks and have given up. I intiated two service tickets and have tried to contact them via phone to no avail. Their recording tells me to email or chat with them. I've tried to find the portal to do that it just sends me in circles. Do you know to get through to them?
rcoop wrote:
Do you know to get through to them?
Maybe PM one of the netgear folks here (JennC?)
rcoop wrote:
Is what you refer to as the OS called Raidiator? And how would the OS partition become full?
RAIDiator is the firmware. It uses linux as the operating system, and is installed to its own partition on your disks. That partition is only 2 GB.
There are several ways for the OS partition to become full. Many involve add-ons that you don't use. However, one scenario is that a log file gets flooded with events and fills up the disk.
I want to underscore that the filling OS partition diagnosis isn't certain, it could well be something else. But if that's what it is, it is easily fixed by Netgear (booting up in tech support mode)
A factory default would also cure it, but of course you'd lose the files that didn't get backed up.
NETGEAR Academy
Boost your skills with the Netgear Academy - Get trained, certified and stay ahead with the latest Netgear technology!
Join Us!
