NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
Solved
ReadyNAS 204 won't load admin page
I have a ReadyNAS 204 with firmware 6.10.7 and four 8TB drives. Have had it 4 years (bought it gently used) and it ran without any issues. I don't run any apps on it, I only use it to store media f...
If you power up with three drives you'll know immediately if you've solved the problem. Your volume will mount, though it will be listed as "degraded" due to lack of redundancy, and you should have access to the GUI. Then when you insert the new drive into the empty bay, you should see the NAS recognize it and begin to sync.
If you power up with the replacement already in place, it will start to re-sync immediately and if you can't get into the GUI, you won't know if it's because the sync is hogging too much CPU or something else is (still) wrong.
Maeve1956 wrote:
Could the failing drive have something to do with this?
It could. Generally Netgear runs the web server at a lower priority than other services. If the drive is generating a lot of errors, then that sometimes does result in a non-responsive web ui.
It's also conceivable that the errors resulted in a full OS partition (due to the error logging). That can result in a lot of odd symptoms, including a broken web ui.
Maeve1956 wrote:
I don't know what to try next.
Since you are backed up, data safety is not a concern.
If ssh is enabled, you can try using that to see what is going on.
Assuming no ssh, options I see are
- purchase a replacement drive, and hot-swap with the failing one.
- pull the failing drive now, and see if the web ui starts working normally again.
- do a factory default from the boot menu. If the system works normally again, reconfigure the NAS and restore the files from the backup.
I honestly can't remember if SSH is enabled. I think so, but I set this up 4 years ago and haven't had to make any major changes and so I haven't been to that screen lately. I can't verify since I can't get into the admin page.
I've never used SSH, but I'm sure I can find instructions on using it somewhere and figure it out.
Based on what you say (which I suspected), I think my priority now should be replacing the drive. I've never done that either, but I believe the manual has instructions, and as it's a hot swap drive it should be a piece of cake.
Thank you for replying.
Maeve1956 wrote:
I honestly can't remember if SSH is enabled.
My guess is that it is not.
But you can test it easily. If you are using windows, enter ssh root@nas-ip-addess in the windows search bar (using the real NAS IP address of course). From a Mac you can open terminal and enter the same command.
If ssh is enabled, youi'll probably get a message asking to confirm a fingerprint (say yes), and then you'll get a password prompt.
If it's not enabled, you should get a connection refused message, or possibly the text box will just close.
Maeve1956 wrote:
it's a hot swap drive it should be a piece of cake.
A hot-swap is what I always recommend. The main thing is to make sure you pull the right drive. If you get that wrong, then you can lose data.
FWIW, I always test my replacement drives in a Windows PC first, using vendor tools. Seatools for Seagate, and Dashboard (or Lifeguard) for Western Digital. I run the full non-destructive test, and also a full erase/write zeros test. Some out-of-the-box drives have passed one of these tests, but failed the other.
I have ordered a new disc, it will be here on the 14th.
SSH is not enabled.
Meanwhile, the error messages I get say "Detected increasing pending sector: count [4224] on disk 2 (Internal) ". Now all I have to do is figure out is which one is disc 2.
The Hardware manual does not give me this information. Is disc 1 the one on the farthest left, or the one on the farthest right??? Normally I would assume Disc 1 is the one on the far left, but it is never wise to make assumptions with hard drives.
You'd think they'd provide this information in the Hardware manual, but they don't, and neither does RAIDar.
Do you know if I count from the left, or from the right?
I don't know what you mean by "could have resulted in a full OS partition." Can you explain what that is and how it works, please? Thanks.
The OS partition on the NAS is quite small, and some programs have been known to fill it up. If enabled, you should have received email alerts about it. But with the GUI not working, the alerts may also no have. The only way you will know is to go into the NAS via SSH and check.
NETGEAR Academy
Boost your skills with the Netgear Academy - Get trained, certified and stay ahead with the latest Netgear technology!
Join Us!
