NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
ReadyNAS Ultra 6 space upgrade
I've been away from the forum for a while now and my ReadyNAS Ultra 6 NAS is filling up. I currently have (6) 2TB disks. I'd like to upgrade to (6) 4TB disks.
Can I just replace each disk one by one with larger drives until all drives have been replaced? I was reading about some sort of "8TB limit" issue and "16TB hard limit"? Now real clear on what that means for my upgrade plan. Am I going to have to reset to factory defaults in order to upgrade my disks from 2TB to 4TB?
Thank you!
8 Replies
Replies have been turned off for this discussion
Assuming you are still runing RAIDiator 4.2.x, then there is an 8TB delta expansion lmit and a 16TB overall expansion limit. If the 2 x 2TB volume you have now is where you started (not with something smaller you added drives to), then you can only replace four of the 2TB with a 4TB before you hit the 16TB limit. If you started with a smaller volume, you might hit the 8TB limit before that. You can factory default with all the 4TB in place, but you'd be unable to expand from there.
One option, though it also requires a factory default, is to convert your unit to run OS6. You gain a lot doing so, including no expansion limit, though you also lose all Netgear support. And if you are going to do that, you are better off starting with fewer, larger drives. Up to a point, you get more TB per $$$ with larger drives, and leaving slots empty makes further expansion cheaper. 3 x 8TB would be a big addition over what you have now and only a bit smaller than 6 x 4TB, and you can later add another 8TB by just adding one 8TB drive where adding 8TB to a 6 x 4TB drive system requires replacing 3 with an 8TB.
My apologies - I am already running 6.10.4 Hotfix 1 on my Ultra 6. So I don't have to worry about any expanion "limits" since I'm on 6.10.4.1?
While it would be nice to replace the disks with (3) 8TB disks, that would require a factory reset and I don't have another copy of the data anywehre - nor do I have anywhere to copy it to. :-) It's mainly movies and TV shows - nothing critical, but a large collection.
So I would be able to replace the (6) 2TB disks with (6) 4TB disks, one at a time until each finishes the rebuild, in order to double my capacity? I realize that it's a long process, but no data loss that way.
I didn't realize that anything over 4TB disks were supported with this old unit. Compatibility charts only show up to 4TB disks. So 8TB disks should work?
Thanks for your help - you've been a big help with this thread and another you recently replied too. I appreciate it!
jtrosky wrote:
My apologies - I am already running 6.10.4 Hotfix 1 on my Ultra 6. So I don't have to worry about any expanion "limits" since I'm on 6.10.4.1?
Correct. Those limits only apply to 4.2.x firmware.
jtrosky wrote:
I didn't realize that anything over 4TB disks were supported with this old unit. Compatibility charts only show up to 4TB disks. So 8TB disks should work?
The HCL for legacy NAS hasn't been updated in years (back when 4 TB was the largest disk size on the market). There is no known ceiling for the disk size in systems running OS 6 - including legacy NAS. So 16 TB should also work. Though sync times will obviously get longer, and you will eventually run out of memory. If you are still running the stock 1 GB of RAM you should consider upgrading. 2x2GB is reasonably available and affordable. 2x4GB is possible - but compatible 4 GB modules are hard to find and expensive. 2x2GB will match the RAM in the RN526, so it is certainly enough.
My own Pro-6 running OS-6 is currently has 2x8TB+4x3TB (20 TB volume)
jtrosky wrote:
While it would be nice to replace the disks with (3) 8TB disks, that would require a factory reset and I don't have another copy of the data anywehre - nor do I have anywhere to copy it to. :-) It's mainly movies and TV shows - nothing critical, but a large collection.
So I would be able to replace the (6) 2TB disks with (6) 4TB disks, one at a time until each finishes the rebuild, in order to double my capacity? I realize that it's a long process, but no data loss that way.
Large USB drives for backup are actually pretty affordable. You might want to look into that - even though your media isn't critical, it still would take time and effort to replace it. Even if you avoid the factory reset, there is some risk when replacing disks or expanding the array. There is no RAID redundancy during the process, so if an existing disk fails you will lose the volume.
You can certainly upgrade one disk at a time, but there is no need to upgrade all six. XRAID will handle unequal size disks - the capacity rule is "sum the disks and subtract the smallest".
3x8TB + 3x2TB would give you 22 TB for about the same money as 6x4TB (current US amazon pricing is about $600 for three 8 TB Seagate Ironwolf or WD Red Plus drives). Plus expansion is much faster, since there are only three resyncs needed. Also, you can further increase storage later by just upgrading one other 2 TB drive to 8 TB.
Similarly, 2x10TB + 4x2TB would give you 18 TB for about $520, and you could increase storage by upgrading one more 2 TB drive to 10 TB later on.
One limitation of XRAID - when upgrading storage, the replacement drive generally needs to be at least as large as the biggest drive in the array. Though if a 2 TB drive fails, you can replace it with another 2 TB drive.
NETGEAR Academy
Boost your skills with the Netgear Academy - Get trained, certified and stay ahead with the latest Netgear technology!
Join Us!
