I have an RBR50 and a RBS 50 sat that are working great. I added the RBW30 and I can't get it to sync. I tried adding a sat through the app and manually and neither option works. Any suggestions how to get the RBW30 to sync

You may need to connect a pc via ethernet to the satellite and login to the unit using its IP address and do a manual update of the unit to the same firmware your orbi unit is currently on. by default the IP address may be 192.168.1.250 but it could of changed since you have tried to connect the unit. DarrenM

The satellite doesn’t have a Ethernet port on it

I suggest contacting support they will be able to troubleshoot with you and replace the unit if it turns out to be faulty. http://www.netgear.com/support/contact.aspx DarrenM

I've been experiencing similar issues. Tell me, does the RBW30 have an IP address and show up in the connected devices table? My theory, and I've not been able to test this, is that becuase my wireless is set up for Daisy Chain, the 2nd satellite needs to sync to the 1st satellite, not the router. Is your wireless set up for daisy chain [Advanced Setup->Wireless->Enable Diay-Chain Topology]? Perhaps try unchecking that box, *or* syncing satellite 2 to satellite 1. Curious to know the outcome...

Can you add the 30 thru the routers web page add satellite feature? I would check to make sure the 30 series is compatible with the 50 series system. I would recommend using same models series satellites as they would be more compatible and maintain same speed ratings they are designed for. Kind of a match system if you will. Test each setting with Daisy chain enabled or disabled to see if it will sync...

RBW30 wont't Sync | NETGEAR Communities

13 Replies

DarrenM
Sr. NETGEAR Moderator
Jan 30, 2018
You may need to connect a pc via ethernet to the satellite and login to the unit using its IP address and do a manual update of the unit to the same firmware your orbi unit is currently on. by default the IP address may be 192.168.1.250 but it could of changed since you have tried to connect the unit.

DarrenM
- brettboz28
  Aspirant
  Feb 05, 2018
  The satellite doesn’t have a Ethernet port on it
  - DarrenM
    Sr. NETGEAR Moderator
    Feb 06, 2018
    I suggest contacting support they will be able to troubleshoot with you and replace the unit if it turns out to be faulty.
    
    http://www.netgear.com/support/contact.aspx
    
    DarrenM
FURRYe38
Guru - Experienced User
Apr 05, 2018
Can you add the 30 thru the routers web page add satellite feature?

I would check to make sure the 30 series is compatible with the 50 series system. I would recommend using same models series satellites as they would be more compatible and maintain same speed ratings they are designed for. Kind of a match system if you will.

Test each setting with Daisy chain enabled or disabled to see if it will sync...
- jftobolski
  Aspirant
  Apr 05, 2018
  yes i have tried it through the web page. no dice. i’ve not tried it via the buttons yet. fwiw you’re supposed to be able to mix and match
  - FURRYe38
    Guru - Experienced User
    Apr 05, 2018
    Well i know for my system, I use the routers UI and use the add Satellite feature. There is a sync button there then I after the satellite is factory reset, I hit the sync button on the satellite. After a couple of minutes, the satellite is online and shows BLUE Led.
    
    I presume you can however device speeds differ between RBS models. The 50 series is a 1700Mb connect rated system. I believe the 40 and 20 series are 800Mb range. These speeds are just speeds between the router and the satellites and devices. Thruput is completely different
    
    You might look at the different specs on the Orbi product page to see what differences there are. I would try to keep in the same rated speeds. If you have a higher speed, then keep with this. Should be less problematic.

Forum Discussion

RBW30 wont't Sync