NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
M4300-8X8F no connectivity with Juniper EX3300 (Juniper DAC) Second turn
Hello. swapped last device by RMA and got the same trouble as it was later - no connectivity between EX3300 and M4300 https://community.netgear.com/t5/Managed-Switches/M4300-8X8F-no-connectivity-with-Juniper-EX3300-Juniper-DAC/m-p/1237316 (10g-ntgr) #show fiber-ports optics-info all Link Link Nominal Length Length Bit 50um 62.5um Rate Port Vendor Name [m] [m] Serial Number Part Number [Mbps] Rev Compliance -------- ---------------- --- ---- ---------------- ---------------- ----- ---- ---------------- 1/0/1 Amphenol 0 0 APF13360028MY0 584990002 10300 A DAC 1/0/2 CISCO-TYCO 0 0 TED1552BVNJ 1-2053783-2 10300 P DAC 1/0/3 CISCO-TYCO 0 0 TED1546BA54 1-2053783-2 10300 P DAC 1/0/4 CISCO-TYCO 0 0 TED1546BA1S 1-2053783-2 10300 P DAC 1/0/5 CISCO-TYCO 0 0 TED1546BA7K 1-2053783-2 10300 P DAC 1/0/7 CISCO-TYCO 0 0 TED1601BSZA 1-2053783-2 10300 P DAC 1/0/8 CISCO-TYCO 0 0 TED1552BVQC 1-2053783-2 10300 P DAC (10g-ntgr) #show fiber-ports optics all Output Input Port Temp Voltage Current Power Power TX LOS Fault [C] [Volt] [mA] [dBm] [dBm] Fault Status -------- ---- ------- ------- ------- ------- ----- --- ------------- 1/0/1 N/A N/A N/A N/A N/A N/A N/A Remote Fault 1/0/2 N/A N/A N/A N/A N/A N/A N/A No Fault 1/0/3 N/A N/A N/A N/A N/A N/A N/A No Fault 1/0/4 N/A N/A N/A N/A N/A N/A N/A No Fault 1/0/5 N/A N/A N/A N/A N/A N/A N/A No Fault 1/0/7 N/A N/A N/A N/A N/A N/A N/A No Fault 1/0/8 N/A N/A N/A N/A N/A N/A N/A No Fault (10g-ntgr) # (10g-ntgr) #show fiber-ports optics-eeprom all Port 1/0/1 vendor_name = Amphenol vendor_sn = APF13360028MY0 date_code = 130905 vendor_pn = 584990002 vendor_rev = A eeprom data = 03 04 21 00 00 00 00 00 04 00 00 00 67 00 00 00 ..!.........g... 00 00 03 00 41 6d 70 68 65 6e 6f 6c 20 20 20 20 ....Amphenol 20 20 20 20 00 41 50 48 35 38 34 39 39 30 30 30 .APH58499000 32 20 20 20 20 20 20 20 41 20 20 20 01 00 00 fa 2 A .... 00 00 00 00 41 50 46 31 33 33 36 30 30 32 38 4d ....APF13360028M 59 30 20 20 31 33 30 39 30 35 20 20 00 00 00 f6 Y0 130905 .... 37 34 30 2d 30 33 30 30 37 37 20 52 45 56 20 30 740-030077 REV 0 31 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 1 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ how to fix it? thanksXS708T 10G/1000M Long Auto Negotiation
Hi guys, I have a XS708T 10G switch for communicating to 2-4 ethernet cameras at a time.The cameras can either be 10G enabled or 1G only, but i have noticed during the camera boot up, the auto negotiation of the switch can take minutes before it finalizes on a rate and connects to the PC. This happens even if i force the ports into 10G or 1000M. If i go directly into the PCI ethernet card, camera connects immediately and I have no problem. I do need these to be networked though, but its extremely unreliable at this point. has anybody else seen this, any ideas?