NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Assigning an Insight Cloud Uplink Port
I'm trying to reconfigure my home network ahead of a fiber install next week. My goal is to connect my Netgear switch to my Unify Dream Machine Pro Max via a 10G DAC (port 10 on the switch) and to my Wifi AP on the 2.5 gig port 1 of the switch. I have my network segregated into five (5) VLANs (1 Management, 2 Secure, 3 Guest, 4 IoT, 5 Cameras) and I can't seem to get my port configuration correct. I think I want to assign ports 1 and 10 (to the AP and Gateway) as Trunk Ports but as soon as I do Insight loses its Uplink Port. If I plug in another cable from the gateway and unplug port 10 it reconnects and the "Uplink" switches to port 8 (the newly plugged in port). When I then reconnect port 10 it takes over as the uplink and the router blocks port 8, IIRC having 2 lines connected between the same devices can cause a loop/flood so I can kind of understand why it would do that. So, if assigning port 10 as a trunk for all of my VLANs kills the uplink to Insight how do I configure the ports to Trunk my VLANs from Gateway-->Switch-->AP while maintaining an uplink to Insight? Is there a way to permanently assign port 8 (or another port) to the cloud uplink while allowing the trunk ports between all three devices? I eventually intend to move my PC and some storage over to the switch but I can't until I figure out how to get all three devices talking to each other properly.MS510TXUP which sfp+ transceovers?
Hi, Which sfp+ transceivers are officially suggested for MS510TXUP please? I have pair of Mikrotik as they auto negotiate below 1G and up to 10G inc 2.5G & 5G in between and where £60 each. The Netgear ones I've seen online are £300 each and don't know why? Any advice please?GC752X - Insight alerts, multiple times per day, false reporting
I continually receive emails telling me that the switch is offline (when it's not) and then when it supposedly comes back online.... Like this: The following device resumed communication with the NETGEAR Insight cloud service at approximately 21-Sep-2023 11:18 What can I do to fix this? This happens repeatedly some days, and then we'll go for weeks without any issue. Very annoyingGC510P shows disconnected but is working
Symptom: Insight shows 4 of my 6 switches as disconnected, but they are working fine. I have 6 GC510P switches at a location. When looking at the switches, they all show they are connected to the Internet (blue light is on). They are all functioning properly (various cameras and access points on separate vlans all work). When I use Insight to look at the switches, 4 of them show "device is disconnected"; it's been this way for over a week. They got out of sync when I upgraded the firmware. In the past, they only way I could get Insight insync with the switches is to manually reboot each switch. The location is connected to the network using an airbridge. I don't know if this impacts something. Any ideas on why the hardware isn't in sync with Insight? TIA, LouisGC752XP Switch Firmware 1.0.5.38 Issues high CPU Rebooting
I started having issues recently on firmware 1.0.5.38 with high CPU and random reboots after using more ports than normal. I have IGMP snooping disabled on VLAN's and have two Insight switches. I noticed I had a POE camera that was flapping a port due to it's own issues, so the port and POE were turned off. However, the switch issues continued. I was able to downgrade to 1.0.5.36 and unplugged everything from the switch except LAN and Internet access. Booted and connected to Insight fine. Thought maybe corrupt firmware update through Insight, I manually downloaded from website and installed back 1.0.5.38 through local console. Shortly after booting it went back to 90+% utilization and after 6 minutes rebooted. Further reboots all yielded same issue. I've been on FW 1.0.5.36 continuously for over a day and not having any issues with CPU utilization around 20%. So I'm eliminating any hardware issues with connected devices or the switch itself as it's been stable on this version.GC728X SFP+ only 1Gb
Hi all, for me is the first time to ask to community to help me to solve an issue on this switch. I have a problem with one on 2 SFP+ port where, when i connect 10 Gb device, port still using 1 Gb; i tried to force to 10 Gb but never changed. If I attach this device to another SFP+ port on another switch connection speed are 10 Gb as same if I attach this device on second SFP+ port in this switch. The second SFP+ port running as expected at 10 Gb. xg27 CISCO-FINISAR 0 0 FNS17492H7U SFP-10G-LR 10300 10GBase-LR Yes 1G xg28 OEM 0 0 S190102022896 SFP-H10GB-CU2M 10300 R DAC Yes 10G Anyone can help me? Thanks BirobyXSM4348FS stack -link shows as offline
Hi, I have a stack of two XSM4348FS-100NES, I configured ports 45,46, and 47 as stack ports. The link is not showing when I am connecting port 45 of both switches using SFP AGM732F-R and 2 meter SM patch cord. port 47 I am connecting using cat 6 cables, which is coming up .Do I need to use a DAC cable or any other issue? #show stack-port Configured Running Stack Stack Link Link Unit Interface Type Product Name Mode Mode Status Speed (Gb/s) ---- ---------------- ------- ----------------- ---------- ---------- ---------- ------------ 1 0/45 SFP AGM732F-R Stack Stack Link Down 10 1 0/46 Stack Stack Link Down 10 1 0/47 Stack Stack Link Up 10 2 0/45 SFP AGM732F-R Stack Stack Link Down 10 2 0/46 Stack Stack Link Down 10 2 0/47 Stack Stack Link Up 10 show switch Management Standby Preconfig Plugged-in Switch Code MAC SW Switch Status Model ID Model ID Status Version Address --- ----------- --------- ---------------- ---------------- ------------- ----------- ------------------- 1 Mgmt Sw M4300-48XF M4300-48XF OK 12.0.17.9 8C:3B:AD:72:2A:B4 2 Stack Mbr Oper Stby M4300-48XF M4300-48XF OK 12.0.17.9 8C:3B:AD:72:2B:7CS3300-28x Telnet connection problem
Hello, I'm having a problem acquiring telnet connection to the S3300-28x. I have enabled Remote Debugging, but this doesn't affect the ports. I've scanned the IP via nmap tool and the only available port is 80, which is TCP for HTTP connection. Default port 23 doesn't work, nor port 24 does. What am I missing?