NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
SNMP
5 Topics
snmp issue with 6.6.0
Since upgrading to 6.6.0 I'm no longer able to monitor disk usage using snmp. I've been using cacti to graph my 312 for the last 2 years. The system disk and the two disk in the NAS no longer appear when I query the device. With snmpwalk I still see swap, memory etc but not the physical disks. HOST-RESOURCES-MIB::hrStorageDescr.1 = STRING: Physical memory HOST-RESOURCES-MIB::hrStorageDescr.3 = STRING: Virtual memory HOST-RESOURCES-MIB::hrStorageDescr.6 = STRING: Memory buffers HOST-RESOURCES-MIB::hrStorageDescr.7 = STRING: Cached memory HOST-RESOURCES-MIB::hrStorageDescr.8 = STRING: Shared memory HOST-RESOURCES-MIB::hrStorageDescr.10 = STRING: Swap space HOST-RESOURCES-MIB::hrStorageDescr.36 = STRING: /dev/shm HOST-RESOURCES-MIB::hrStorageDescr.37 = STRING: /run HOST-RESOURCES-MIB::hrStorageDescr.38 = STRING: /run/lock HOST-RESOURCES-MIB::hrStorageDescr.39 = STRING: /sys/fs/cgroup I've tried adding the disks to snmpd.conf and restart but I can't see them. disk / 5% includeAllDisks 5%6.6KViews0likes16CommentsRN104 - does it support UPS managed over USB?
I am thoroughly confused. Does RN104 support UPS monitoring over USB? ReadyNAS OS 6.4 Software Manual states: "The ReadyNAS supports UPS devices managed over SNMP and UPS devices managed over a remote connection. It does not support monitoring over USB." ReadyNAS OS 6.6 Software Manual states: "The ReadyNAS supports UPS devices managed over SNMP, USB, and over a remote connection." Am I correct in assuming that the RN104 now accepts UPS with USB connection whereas it didn't before? (which was not long ago). I have yet to find a reasonably priced UPS supporting SNMP (i.e. under £100). Most support USB though, so that seems the only route.Solved3.9KViews0likes2CommentsRN4220 and SNMP connected UPS
I have a readynas 4220 running firmware 6.4.0. It is connected to a network enabled UPS. ( APC Symmetra LX 8000 RM ) I am polling the UPS with SNMP v1. I am getting " System: Error communicating with UPS 'Symetra' () " then 10 sec later " System: Communication with UPS 'Symetra' () is OK. " This runs in spurts. Quiet for a few hours, then 16 in about 2 hours of time. The UPS is not logging any alerts or error activity. Is this a proven connection method with a UPS? Or a feature that is not used much or is troublesome? I have 3 network connections running to the switch. 1g and 10g copper. Should not be a bandwidth issue. Garet4.6KViews0likes4CommentsReadyNAS Ultra 6 SNMP addon
Hi all, I have had to reset my ReadyNAS Ultra 6 to defaults, and have lost the SNMP addon. I cannot locate it on my own PC, or on any of the forums. I have searched for hours with no success. Would anyone out there have the .bin file still available and be able to post it or email it to me please? Thanks in advance.Solved
[RN104] How to set up UPS monitoring?
Via searching I've come across several posts that address only parts of what I'd like to do, but aren't applicable to the task as a whole. Here's my setup: RN104 Hyper-V 2012 R2 (Server Core chopped off at the knees—CLI only) APC SMC1000 (no networking w/this model) I've got some iSCSI LUNs on the RN104 that're used by the server, thus the server needs to shut down first—preferably at least five minutes sooner. What's my best approach? Should the NAS somehow push a command out to the server or should the server poll the NAS? How would I do this in any case? Thanks, Jeff Bowman Fairbanks, Alaska4.2KViews0likes7Comments