NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Nighthawk m2, Mobile Broadband getrennt
Hallo zusammen Ich habe einen Nighthawk M2 und benutze eine SIM-Karte eines schweizer Mobilfunkanbieters. Das Gerät funktioniert in der Schweiz perfekt. Sobald ich es im Ausland verwenden möchte, erscheint die Meldung "Mobile Broadband getrennt" und ich kann den Router nicht verwenden. Das Int. Roaming ist auf "ein". APN des schweizer Anbieters eingestellt. Was muss ich tun, um den Router auch im Ausland verwenden zu können?Nighthawk M.2 hat kein WIFI mehr
Hallo zusammen, ich habe einen Nighthawk M2 Mr 2100 mit Firmware NTX24_10.19.03.00 Hardwareversion 1.0 umd Pri 05.02. . Seit gestern habe ich auf einmal keine Wlan mehr aktiv. Das Wlan synbol ist mit einem Roten Kreis und einem weißem Kreuz zu sehen. Faktotra reset über die Software, Danach über den Knopf im Batteriefach, alles mehrfach ausgeführt, mit Batterie und ohne, Das Reset wird im Display angezeigt, aber das Wlan ist unverändert inaktiv. Ich würde gerne die Firmware erneut installieren, aber ich finde keinen Download. Was kann ich tun ?Nighthawk M2 offloading problem
Hey, I use the Nighthawk M2 MR2100-EUS in my camper car and use it in two modes With a German simcard With Data offloading via Ethernet (Starlink antenna is attached via adapter, no Router involved). I encounter the following problem: When I change countries while driving most of the time the router needs a restart to connect to the new network. And it is not only when leaving Germany but also e.g. when driving from France to Spain - so from one foreign network to the other. Also I like to use the Starlink power save mode where it shuts down at a certain time (1:30 in my case) and starts up automatically in the morning (8:00). The router does not connect again. I need to restart so that offloading works again. Normally I would expect it switches to mobile in this time or it has no internet. both would be ok but it should go online again in the morning... Any Ideas? Nighthawk M2 Hardwareversion 1.0 GUI-Version MR2100-100EUS_04.02.171.00 Firmwareversion NTGX24_10.19.03.00 PRI-Version 06.03 Modemversion SDX24_10.25.02.03 Firmware-Erstellungsdatum 2021/09/01 Thanks and best, JosefMR2100 - Wireless access point via ethernet
Hi just wondering if the MR2100 can be used to extend an existing service as a wireless access point from an existing router by ethernet. Unable to find any options. Essentially i want to plug an ethernet cable into my device from a network so i can wirelessly connect into it. ThanksSIM unlock domains not working
Hello, My unlocked M1 connects to my devices, I’m all logged in, and the signal works, but I am prompted to unlock my SIM to connect to Internet. However, the suggested http://attwifimanager and routerlogin domains and IP domain do not load I have cleared cache and done everything suggested. There is no support for M1 on mobile app Any advise would be much appreciated Traveling in ItalyTwo Netgear Nighthawks, MR1100/2100
Hi, I apologise in advance if this has been covered elsewhere or if this is not the correct forum for this question. I have two Telstra (AU telecom provider) Netgear Nighthawk 4G mobile broadband modems (M1 & M2 in Telstra parlance, so MR1100 & MR2100 in Netgear-speak) for home use (batteries out, mains-powered only) as well as a small pocketable ZTE MF910 4G modem mainly for use in my car or when out and about (all modems remain on, so transmitting & receiving throughout the day). The 2019-2020 bushfires that devastated our region here on the far south coast of NSW in AU did nothing to improve our telecoms infrastructure here and with no fixed (NBN) internet in our home, I acquired the two modems to enable a (relatively) reliable internet connection. To enable this, I have 3 different SIMs from 3 different providers (mobile reception often doesn't work on one or the other from time to time, so I just switch to a different modem). The MR1100 one is connected by Ethernet to an Apple Airport Time Capsule to provide computer backups, WiFi coverage & printer access throughout the apartment. Preamble over, given that there are two Netgear Nighthawk MR-type modems, is there any problem that they have the same gateway 192.168.1.1 (apart from the administration web page being the same), despite the IP addresses being different (2˚ to different ISPs)?
