Site to site iPSec VPN with two BR500 VPN router

SCCHANG
Tutor
Dec 13, 2022
DaneA,

I read through the entire manual section of the Netgear BR500 IPSec VPN set up section and also looked at that KB article you suggested. Everything matched between the two BR500 routers and I double checked a few times already to make sure I didn't miss anything. With the BR500 IPSec settings previously worked with the Netgear SRX 5308 router which I copied to the second BR500, it should then worked, but it didn't. Changing to the default IPSec VPN settings suggested by the manual which is basically the same as the KB article but it still did not work...

Did anyone have similar experience or have two BR500 working site to site in a IPSec VPN connection? I would appreciate sharing with me what you have/configure to get it working.

Thank you for the help.

Sun
SCCHANG
Tutor
Dec 19, 2022
Hi DaneA,

You replied back to me before about my problem. At about the same time, I received a reply message from another Netgear support admin which I overlooked. I thought about it a few days ago (I'm travelling and currently out of the country now.) as the message came with a link to Version 5.6.... firmware without any other information. At that time I didn't think more about it as I have been running Ver 5.10.... firmware already. Is it possible that I should download an older version firmware to make the site to site iPSec VPN work? I searched on the Netgear community site and also in my email account, but could not locate that message again. Could you please help to confirm that:
1. Should I download the older version firmware?
2. What version is it? I can only remember it is ver 5.6... but don't know the exact version.
3. Would there be any problem if I replace the latest firmware with an older firmware?

Thank you in advance for your help.

Sun
- DaneA
  NETGEAR Employee Retired
  Dec 21, 2022
  SCCHANG,
  
  You may want to downgrade the firmware to an earlier version in order to isolate the problem. Just be reminded that downgrading the firmware will not have the enhancements and bug fixes of the later (or latest) firmware version.
  
  You can check the older BR500 firmware version here.
  
  If ever you are not yet aware as this might be related with the VPN issue you encountered, let me share the article below:
  
  Security Advisory for Multiple Security Vulnerabilities on BR200 and BR500, PSV-2021-0286
  
  Regards,
  
  DaneA
  
  NETGEAR Community Team
  - SCCHANG
    Tutor
    Dec 26, 2022
    Hi,
    
    Our school is still in winter break and I have not been able to try downgrade the BR500 firmware. I read a little about Insight cloud service and wonder whether we're better off to use it for our site to site VPN. I have questions after reading a bit about Insight online for our site to site VPN connection:
    1. It says cost is $9.99 per year for one device, that means for our two sites with 2 BR500, it costs $19.98 per year, am I correct?
    2. Do we need to have both BR500 running the latest firmware which is V 5.10.0.5? (Before I try to download their firmware...)
    3. Any limitation with using Insight instead of direct VPN between 2 sites with BR500?
    4. What is the experience of disconnect or up time (e.g. 95% up time or better...)?
    5. Any link you could provide in setting up Insight quickly with the proper steps?
    
    Thank you,
    
    Sun

Forum Discussion

Site to site iPSec VPN with two BR500 VPN router

Related Content

BR500 VPN and IPSec Example w/Open Source

BR500 IPSec - Can't set Aggressive Mode

BR500 - Instant VPN Router

Site-to-site IPSec VPN & More for BR500 Router Updates with Insight IM5.6 Release

BR500 IPSec Windows ports appear to be filtered

NETGEAR Academy

ProSupport for Business