The NV+ has 3 x 2.0 usb ports yet the pci_devices.log states 2 of the ports are 1.1

Question

Hi&nbsp;As I stated in subject the&nbsp;pci_devices.log reports 2 of the usb ports as 1.1(see below) but NV+ is supposed to have 3 x 2.0 usb ports 1 front 2 rear.&nbsp;So if that is the case that 2 of the usb ports are 1.1 which of the ports is 2.0, front or back?Thanks&nbsp;Art&nbsp;pci_devices.log0000:00:17.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61) (prog-if 00 [UHCI])&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Flags: bus master, medium devsel, latency 128, IRQ 27&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; I/O ports at 5c001000 [size=32]&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Capabilities: [80] Power Management version 2&nbsp;0000:00:17.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61) (prog-if 00 [UHCI])&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Flags: bus master, medium devsel, latency 128, IRQ 27&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; I/O ports at 5c001020 [size=32]&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Capabilities: [80] Power Management version 2&nbsp;0000:00:17.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 63) (prog-if 20 [EHCI])&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Subsystem: VIA Technologies, Inc. USB 2.0&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Flags: bus master, medium devsel, latency 128, IRQ 27&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Memory at 000000005c010000 (32-bit, non-prefetchable) [size=256]&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Capabilities: [80] Power Management version 2

StephenB · Answer

Per the hardware manual (&nbsp;https://www.downloads.netgear.com/files/GDC/RND2110/Duov1_NV+v1_HW_en_06Dec11.pdf ) all three of the USB ports are 2.0.
&nbsp;
Not certain about this, but I believe that USB 1/1.1 devices end up using one of the UHCI controllers (even though they are plugged into a USB 2 port).

art305 · Answer

&nbsp;Yes I see what you mean 1.1 UHCI controllers are for compatibility.&nbsp;I will do some more investigating. The logs also give a history of which usb port has what device connect and is using which controller so I will try using each port and see what the logs say.&nbsp;Art

Forum Discussion

The NV+ has 3 x 2.0 usb ports yet the pci_devices.log states 2 of the ports are 1.1

2 Replies

Related Content

Nighthawk m1 - 5510 port state: filtered

BPDU Handling und Spanning Tree State

RN21400-100AJS last power state

WAX206 - Shelly not able to keep state

RBRE960 LAN PORTS DROPPING

NETGEAR Academy

ProSupport for Business