NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Disk reuse after factory default
I am using ReadyNAS RN316. There was some problem occurs ,so I remove the 6 disk(raid5 array created) then factory default. Factory default success and restart. However if I push the 6 disks back to the trays, RN316 starts formating automatically or ditects the array same as before????ReadyNAS DUO RND2000V2
I was asked by a friend if I could have a look at her RND2000v2. It was "not working" anymore. I started it at my desk, it began to check the disks and started up as far as I can see. I installed RAIDar and it show the device. When I tried to connect the frontview it gave me an error. It said "unsupported protocol". I edited the Virtual.conf file where I replaced in these lines: RewriteRule ^/admin https by http. Now I get the admin prompt when I use http on the NAS/admin but then I get the error: The requested URL /admin was not found on this server. And I don't know how to get the networkshares visible in the windowscomputer. I directly connected the NAS to the networkport of my laptop on which I have set the ip-range in the same range as the NAS is.readyNAS 104 doesn't start properly
Hello community, I'm french so i'm sorry for my english level. Topic: Suddenly my NAS didn't start properly. I pushed on start button and the NAS started but stopped after 2 seconds. I retried but did the same. I have tried to change the electrical plug but didn't change the situation. I have get out the 4 hard drives and the NAS started, booted during 1 min until 100% and writen on the front screen "in safe mode". I tried again installing the 4 hard drives and the problem appeared again. Now i don't access to my datas and i dont know if the hard drives are corrupted or if the problem comes from the NAS itself?! I had the opportunity to get a second identical NAS 104 but i'm afraid to install my hard drives into, starts the Readynas and loose my datas. If i remember well i'm in raid X. My last opportunity is to use RS raid retrieve software but it should be an other story! If anybody has a suggestion please let me know!Replacement PSU for ReadyNAS 628X
I have two ReadyNAS 628X units. They have done well so far, however, yesterday the PSU gave up (just gone 5 years) in one of the 628X during a cold start and the PSU will need replacing or component level repair. Can anyone advise if there is a standard PSU replacement model on the market from the PC market units that fit into the ReadyNAS 628x?Restore RAID to ReadyNAS System
How do I restore my ReadyNAS 316 to full RAID? Before this all started I had 5 disk drives, and my recollection that everything was happily RAIDed. I got an error message that Drive 3 was failing, so I plugged in a new 16TB drive into slot 6. Then all went haywire. The attached picture shows how my system looks now. Only 2 drives (both 6TB) are listed as RAID, while the other four drives, including the new one, are gray. Yet the I have two volumes with 15TB on one and 7TB on the other. Does this mean that some of my data is not fully duplicated? And given that four of my drives are listed as not RAID, does this mean that I can't remove them? And what does it mean that I have four inactive volumes? If these four disks are inactive, how do I store 22TB of data on two 6TB drives? I'm really confused. I don't have another system to copy all the data onto. What can I do to get the ReadyNAS to recover? How can I find out what data is on the "inactive" volumes? If I remove them, do I lose data? Thanks. - MalcolmSystem not recognized in Windows connection
Perfectly operational ReadyNAS 626 system as of one week ago. Installed and recognized for the past three years. Connected and operational on five different Windows workstations. RAIDar can access without issues A windows browse enumerates/finds the device and lists it in browse window Attempts to access device fail -- error message indicating name might have been misspelled. It finds the system on the browse and lists it's name -- the same name as the past three years. Worked fine until most recent Windows automatic update. Any hint what might have gone wrong? Anybody else having these problems?Logon to RN104
I have a problem with my RN104 software version 6.10.5, in that I can't logon to it. I'm on Windows 11. RAIDar finds it okay. I can't ping it, and file explorer can't see it either. Up until recently it has been working fine. I would like to upgrade the software to 6.10.10. Could anyone please point me to where I can find the information to logon to it, and to enable my PC to see it. Regards Keith Dutton (UK)
