NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Netgear R7000
i was getting buffering - checked the modum and that was good- unplugged the router - finally reset it - but when i try to connect the router to my computer with the ethenet cord the routerlogin - the page never loads not sure where to go from here - purchased in 2021 so its not that old and its been a great router with a good range to reach my back field where i monitor bluebirds with a blink cameraR7000P power outage fault
I recently had a power outage for all of 20 seconds and, even though I’ve had many over the years with this router, this time the WiFi didn’t work again and the name of the router started showing up as the standard name instead of what I personalised it to. That is to say, my devices SAY they are connected but there is no actual, working WiFi. I’ve done all the usual work arounds suggested online and even resorted to factory resetting TWICE and I can never get to the end of the set up process in the app. I get as far as the ‘checking cables’ part which clears but it always says there’s no internet connection despite the fact my phone is showing as connected. It suggests turning the router off and on again - which of course I have done a hundred times. I’ve checked my Internet service and that’s all perfect, as it’s displaying on the nbn modem. Firmware was up to date even before all this nonsense and shows as such in the app. It makes no sense to me why all of a sudden it chooses to blow up after a power outage when it’s survived dozens in the past. I genuinely have no idea what more I could do. I know it’s an old machine, is it just time to upgrade?R7960p
I just installed this router and after finally getting it set up I accidentally unplugged it and when it came back up everything went back to the factory settings and now I can't get it to connect. Is this router worth it or sounds like I just need to get another router. Any suggestions? ThanksR7000P - DnsMasq heap buffer overflow vulnerability - Avast CVE-2017-14491
Hallo zusammen. Habe auf meinem Netgear R7000P, gekauft September 2018, folgende Sicherheitslücke festgestellt : CVE-2017-14491 DNS Port 53 diese wurde mir durch AVAST mitgeteilt. Habe die neuste Firmwareversion V1.3.1.44_10.1.23 auf dem R7000P Habe den Netgear Support schon angefragt doch diese konnten oder wollten mir nicht helfen. Netgar hat mich auf www.bugcrowd.com verwiesen, doch da habe ich zuwenig Erfahrung. Kann mir von Euch jemand helfen was ich da am besten tun muss? Den Port 53 einfach sperren? Müsste da nicht Netgear ein neue Firmeware bereitstellen? Vielen Dank eikeiLACP on gigabit ethernet port for R7000P and above
Hello, The device is really cool but I can't understand why there is no LACP... Wifi is faster than the gigabit ethernet ports? Is it really ok for you? I really hope there will be a LACP version of this model, or maybe better... a new firmware with this option. It should be so great for home NAS to perform in good condition HD streaming. Secondly, is it possible to connect a 4G router (netgear AC810AC) on USB3 to make a internet "failover". It should be great too. Thanks for reading me. And thank for the goos job you make on these products. Kind Regards, Nicolas.Router R7100P and AirCard 810 on USB3 ? (request upgrade)
Hello, I have a router R7000P and a AirCard 810(EUS)... Both are Netgear devices so I wished it can be compatible. Is it possible for the development team to make this router able to connect to the AirCard to increase the bandwidth (load balancing mode.... maybe bonding if it is possible?) in additionning the DSL (via ethernet) and LTE-A (via USB). Else it can be a very good way for a failover mode. Waiting for some answer. Maybe I'm not alone to want this kind of feature? Kind regards.
