NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
MS510TXM - Private VLAN Promiscuous Port Issue
Hello, I am following the directions on how to properly setup a promiscuous port on a private vlan that allows communication between the two associated community ports. I am unable to add more than one secondary vlan in the interface and the manual clearly says it's possible so I must be missing some nuance. VLAN Type Configuration 20 - Primary 21 - Community 22 - Community Private VLAN Association Primary 20 --- Secondary 21-22 --- Community 21-22 Port Mode Configuration I8 - Promiscuous (LAG) Private VLAN Promiscuous Interface Configuration Here is page 180 of the manual under: Private VLAN promiscuous interface: Assign the interface to primary and secondary VLANs ... ... 9. In the Promiscuous Primary VLAN field, specify a primary VLAN ID. You can select a VLAN for which you configured the type as Primary (see Assign a private VLAN type to a VLANonpage171). 10. In the Promiscuous Secondary VLAN field, specify one or more secondary VLAN IDs. You can specify VLANs for which you configured the type as Isolated or Community, both of which are secondary VLAN types within a private VLAN. You can specify a single VLAN ID, a range of VLAN IDs, or a combination of both in sequence separated by a comma (,): You can specify an individual VLAN ID, such as 10. You can specify the VLAN range values separated by a hyphen, for example, 10-13. • You can specify a combination of both separated by commas, for example: 12,15,40–43,1000–1005, 2000. ERROR Error: Value (0) is out of range for 'Promiscuous Secondary VLAN'. The valid range is 2 to 4095. I have tried to add 2 secondary vlans with the comma approach 21,22 and with the hyphen approach and both give the same error. The Secondary VLAN field only accepts 1 vlan so how do you configure a promiscuous port in a private vlan?WAC720 bricked
We have a few WAC720 AP's controlled by a WC7500 Wireless controller. So far I have: Performed a hard reset to the AP (holding button down for 10/15seconds) I can only use Putty to conect to the AP via the console port. The state of the AP LED's: power - solid green activity - no light network/lan: no light Thoughts, has anyone found a work arround for this AP? Thanks :)Discovery Tool - no network options in drop down
I am trying to use the NETGEAR Discovery Tool on a relatively fresh installation of Windows 11 Pro. I have confirmed that sharing and network discovery are enabled on the computer, but don't know where else to look. I have another identical computer on our network with the same settings and it works as intended. I spoke with support and they told me to check my services, but they all are running. Any help would be appreciated!Home Account should be Business
Does anybody know how to contact Netgear when you have an admin problem (not tech support). For several years I have emailed different people (sales, support etc) asking why my account is setup as a Home account when it should be a Business Account. I never get a reply. That means that every invoice that I get from Netgear Ireland has VAT on it which I cannot reclaim because it is an Irish VAT number. It should be dealt with under the reverse charge procedure and have no VAT added. So far I cannot find and point of contact to deal with mundane issues such as this but it is costing me money every time I have to renew a support contract and it stops me buying anything direct from Netgear. I am about to spend a few thousand pounds on new Wireless Access Points and I'm seriously thinking of using a different product. Thanks for any help.WAX615 Mehrere APs als quasi Mesh nutzen
Hallo Zusammen, ich habe zwei WAX615 APs und möchte dies noch um einen dritten evtl. sogar vierten erweitern um bspw. die verschiedenen Ebenen/Bereiche einer Immobilie abzudecken: AP1 = Paterre AP2 = Garage AP3 = Garten AP4 = 1. Stock Genutzt werden drei verschiedene SSIDs und Einstellungen: SSID mit nur 5GHz Sendekanal für AP1 40/5,2 GHz Sendekanal für AP2 48/5,24GHz PMF 802.11w optional Band Steering / 802.11 k/v aktiviert SSID mit nur 2,4GHz (Auto Kanal einstellung) PMF 802.11w optional Band Steering / 802.11 k/v aktiviert Gast-SSID mit beiden Frequenzen PMF 802.11w optional Band Steering / 802.11 k/v deaktiviert Allgemein Einstellungen: QoS ist für alle Frequenzen mit WMM und WMM Powersave aktiviert Spannung Tree Protocol aktiviert Network Integrity Check aktiviert IGMP Snooping deaktiviert Ethernet LLDP aktiviert UPnP aktiviert Powersetting 802.3at Load Balancing aktiviert Force Sticky Client ti disassociate deaktiviert Leider war die Anleitung da für mich nicht sehr hilfreich, daher wäre meine Frage: Was wäre die optimalen Einstellungen um die selben SSIDs auf allen APs quasi wie ein Mesh zu benutzen ohne die Insight App zu nutzen und Lokal zu konfigurieren? Viele Grüße und ein schönes verlängertes WochenendeAuto Voice VLAN setup
We are looking to isolate our VoIP traffic to its own VLAN. For a number of reasons, we'd like this to happen without needing to configure each phone. It looks like Netgear switches support this. Unfortunately, the documentation is scattered and in many cases outdated. I'm hoping some folks here can show me where we're going wrong. Goals: Voice VLAN = 88. Ports 1-44 set to untagged VLAN 1 and VLAN 88. Default to 1 unless MAC address prefix matches a VoIP device. Ports 45-46 are for router for Voice-VLAN and has no access to VLAN 1. Ports 47-48 are for router normal VLAN (1) and has no access to VLAN 88. Ports 49-52 are uplinks and should carry traffic for both VLANs. The phone should be able to operate in pass-through mode, and devices behind them should default to VLAN 1 as they normally would. Currently I am facing two issues: When I plug in a phone with matching MAC prefix, it is not being pushed to VLAN 88. I'm unable to outright disable Voice-VLAN (88) on ports 47-48. I'll add some screenshots of the current config in a follow-up post. Hopefully some kind network admin will take a look and be able to spot where I'm going wrong.Share internet between two Vlans on a netgear GS724TV4
Hi So I been trying for altmost 2 days to set up my netgear GS724TV4, which is a managed layer3 switch, but does not have capability to create a DHCP server. I am running a webserver and email server, and would like to seperate this from my private network, in case of hacking. So I though I would make two Vlan, lets say vlan1 for private and vlan100 for the server. ISP fiber to my house -> deco X10 setup (internet Vlan id 101 - 802.1q tag) -> unmanaged layer3 switch that provides my netgear with 2 patch cabels in port12 and 13 I have attached a screenshot of my setup and here is some info: port 2 and 3 my private network. port 12 and 13 - Conntect to an unmanaged switch, where my internet patch-cable is connected. port 24 - my server Since I dont understand inter-routing my idea was to have 2 vlans, where vlan1 had port 1-12 untagged and vlan2 had 13-24 untagged, and both vlans would get internet via port 12 or 13. Could somebody tell me if and how to set this up? Help is greatly appriciated
