NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
EX6150 WiFi range extender drops connection for a few seconds very often.
I have the latest firmware. I'm located a floor above my router and use the EX6150 so that I can get a stronger connection in my room. I've noticed that every hour or so, the connection will drop for a few seconds and then reconnect. I used to own the EX6100 and I never had this problem before. Does anyone have any idea as to what is happening here and why this is happening with the new extender but not the old one? I know that it isn't the extender itself because I also own an EX6400 and the same issue occurs. Things I've tried: - Updated to the latest firmware. - Switched Wifi channels. - Removed devices from my network. - Moved the extender to be slightly closer to my router. - Reset the extender. - Reset the router. - Replaced the ethernet cable the extender connects to my PC with. - Replaced the power strip. I'm really at a loss.Orbi wifi disconnects/crashes caused by Google Home and Chromecasts OFFICIAL
Google has officially acknowledged this issue of wifi networks getting killed by way too frequent MDNS packets being sent from their devices that crash various routers. I will say that I switched to a Linksys after starting to have issues with Orbi late November, and have not had any more issues. I suppose the robustness of the router to handle such traffic comes into play. Google acknowledges wifi issues caused by Home and Cast devices.PS4 Pro Wont Connect to the 5GHz Signal
So I just recently purchased the Orbi RBK40 router and I noticed you cannot separate the 2.4GHz and 5GHz WiFi signals through normal methods. I was told that the router has a system or program that automatically pushes the best connection possible. All the devices that support a 5GHz connection seem to connect just fine. However, there are two PS4 Pros in the house and the router refuse to connect it to the 5GHz conncetion. Under my network settings on both PS4 Pro say they are on a 2.4 GHz conncetion. Even under the router GUI it says that it's connected to the 2.4 GHz conncetion. I've been trying to look up methods on how to connect it mannually but no luck. I found a post that teaches how to separate the SSIDs for both the 2.4 and 5 GHz and it worked, however the devices that were connceting to the 5GHz were experincing lag issues and would not have a consistent download rate. I usually average between 145-150 Mbps download when I don't split the SSIDs. However, when they are separate SSIDs, the download ranges from 6-130 Mbps and is never consistent. Not to mention, when the SSIDs are split, the PS4s seems to disconnect from the router frequently. Long story short, is there a way to connect the PS4 Pro to the 5GHz connection?iphone7 not connection to Orbi
Recently, my iPhone7 will not connect or stay connected to my Orbi wifi. It will show that it's connected under the phone's wifi menu w/ full bars, but the top of the home screen only shows "LTE", no wifi bars/symbol. Every other iOS device in my house, including my wife's iPhone7 works flawlessly. I have reset my phone, reset my phone's network settings. Toggled beamforming/mu-mimo on/off, reset the orbi, reset my Spectrum router. All with no luck. In some instances after a reset, the phone WILL connect to wifi. Then a few minutes later drop the connection and will NOT reconnect. It will show connected, but again displaying "LTE" and no wifi bars. Other times it will not connect at all. My orbi also has the current firmware. I am stumped. Currently, I'm at work and my iphone7 connectes to my work wifi with no issues.Turn off wireless schedule not working as intended
Not sure if its because of the new firmware, but i am not getting the "turn off wirless by schedule" working as intended. Say for example i set period start 9am to 6pm. The wifi signal would go off in 8:30am and when its over 6pm. The wifi do not turn on itself. I have to login to admin page and found that the "enable wireless radio" box was unchecked. To turn the wifi signal back, i have to check the box and apply the setting. This have been going on since day 3 i ever use this feature and it does not make sense. Any one else have this issue? I have fed up and switch back to the normal settings without using this feature. Will monitor my connection these few days and will update. One thing i do notice though, the new firmware has been causing disconnect issue even worse. Not sure if this is the cause. But seems every roll out of new update, the router connection becomes unstable. How do we block auto update of the firmware?+++++++++++ NETGEAR N450 Disconnects Once every hour on the dot - DHCP ISSUES +++++++++++++
Model: NETGEAR N450 (CG3000Dv2) N450 WiFi Cable Modem Router Firmware: V3.01.06 OS: Windows 7 Enviroment: Single Modem, no router, direct wired connection My n450 was working fine for a couple months but this past week it started having problems. Once an hour, every hour, on the dot within a few seconds the N450 will disconnect for about 5 seconds then reconnect. I can precisely predict when it will disconnect before it disconnects and like clockwork the N450 will disconnect. I am not running this on a wireless connection, I have no cable splitters, no router, just a direct connection from the modem to the PC. I have checked the cables from my computer to the modem and the cable from the modem to the wall, and even the crawl space behind the wall leading to the outside cable box, all cables are in perfect condition. I did some research and people are claiming that the issue is a 1 DHCP hour lease and that sounds EXACTLY like the problem I am having. I searched the N450 N450 CG3000Dv2 User Manual and on page 69 the instructions for modifying the DHCP state: ------------------------------------- Reserve an IP Address for DHCP Use To reserve an IP address for DHCP use, enter the DHCP server reservation settings for the private LAN under DHCP Reservation Lease Info in the LAN IP screen. To reserve an IP address for DHCP: 1.Type http://192.168.0.1 in the address field of your web browser. A login screen displays. 2.Enter the modem router user name and password. The default user name is admin. The default password is password. The user name and password are case-sensitive. The modem router main menu displays. 3.In the main menu, under Advanced, select LAN IP. The LAN IP screen displays. 4.In the DHCP Reservation Lease Info section, enter the MAC address of the computer for which you want to reserve an IP address. 5.Enter the permanent IP address for the computer. 6.Click the Add button ----------------------------------- But literally on the third step these instructions stop working. There is no LAN IP button or link anywhere in the Advanced options. There are many threads on this issue for this specific modem with people claiming they are constantly getting disconnected. A common remedy people have suggested is to perform a factory reset so I did just that, but that also did not fix my problem. Here is a collection of threads that people posted with similar issues that I am having to hopefully prove this is not an isolated incident. Getting disconnected like this is incredibly frustrating as a gamer. Many of the games I play are senstive to disconnects and punish the player. For grandma browsing facebook a 1 hour DHCP timer would never be noticed. For me it's incredibly painful because not only do I get interupted once an hour, I have to sit out for 20-30 minutes to wait for the DHCP timer to expire before getting commited in a ranked match. https://community.netgear.com/t5/Cable-Modems-Routers/N450-disconnects-every-hour/td-p/1025699 https://community.netgear.com/t5/Cable-Modems-Routers/N450-WiFi-keeps-disconnecting/td-p/978900 https://community.netgear.com/t5/General-WiFi-Routers/DHCP-Lease-Length/td-p/466827 https://community.netgear.com/t5/Nighthawk-WiFi-Routers/Why-is-there-no-DHCP-Lease-settings-on-a-200-top-tear-router/m-p/1118769#U1118769 Please do not suggest returning the product, it's just insulting because I spent like 100$ to fix my internet problems by purchasing the n450, returning the product would mean 1 week+ with no internet and another 100$+ for another modem. Again I want to repeat what is so frustrating about this issue is that this router was working fine for months, and only a few days ago does this DHCP issue manifest.Netgear WNDA4100 N900 Frequently Disconnects
Hello, I have Window 8.1. I use The Netgear WNDA4100 N900 Adapter. It frequently disconnects and looses its signal. All other wifi devices in the house run well. My computer is the only one that cannot stay on the internet. Is there any help that can be given for this? I am very frustrated. I am constantly removing the plug from the USB port and plugging it back in, to connect to the signal. I have used multiple USB ports and the same issue happens. Thank you for your time.