Unable to add ports to LAG

Hi DaneA,

Thank you for your replying.

1. Are ports 17 & 18 set as tagged (T) ports on VLAN 2004 and VLAN 3088?

Correct.

1. Since you have set LACP (static mode disabled), is this also the same LAG settings configured on the Allied Telesis CentreCom GS908M? Kindly check and compare the Hash mode as well on the M7100-24X and Allied Telesis CentreCom GS908M switches.

I have tried the both of disabled static mode and enable on M7100-24X. But no luck. Also I have tried all the 7 Hash modes. It is quite same. When I add the port into a LAG, the connectivity is lost. As reference, I copy and paste the configuration of Allied Telesis CentreCom GS908M below.

Manager 3tkdtest8hub01> show config dynamic=

#

# SYSTEM configuration

#

set system name=3tkdtest8hub01

#

# CONSOLE configuration

#

set console timeout=0

#

# VLAN configuration

#

create vlan=vlan2004 vid=2004

add vlan=vlan2004 port=1-2 frame=tagged

create vlan=vlan3088 vid=3088

add vlan=vlan3088 port=1-2 frame=tagged

#

# IP configuration

#

add ip interface=vlan3088 ipaddress=192.168.88.50 mask=255.255.255.0 gateway=192.168.88.254

#

# STATIC MAC configuration

#

#

# SWITCH configuration

#

set switch port=1 acceptable=vlan

set switch port=2 acceptable=vlan

#

# TRUNK configuration

#

create switch trunk=uplink port=1-2 speed=1000m

#

# MIRROR configuration

#

#

# IGMPSNOOPING configuration

#

#

# PORT LIMITATION configuration

#

#

# PORT AUTHENTICATION configuration

#

#

# ACCESS FILTER configuration

#

#

# TELNET configuration

#

#

# FTP configuration

#

#

# NTP configuration

#

enable ntp

add ntp peer=192.168.5.242

#

# HTTP configuration

#

#

# LOG configuration

#

#

# SNMP configuration

#

#

# QOS configuration

#

#

# LOOP DETECTION configuration

#

#

# STORM DETECTION configuration

#

#

# EPSR Transit/Aware configuration

#

#

# MLDSNOOPING configuration

#

Manager 3tkdtest8hub01>

--------------------------------

Actually it is pinging without a LAG.

C:\Users\G10092>ping 192.168.88.50

192.168.88.50 に ping を送信しています 32 バイトのデータ:

192.168.88.50 からの応答: バイト数 =32 時間 =16ms TTL=253

192.168.88.50 からの応答: バイト数 =32 時間 =2ms TTL=253

192.168.88.50 からの応答: バイト数 =32 時間 =2ms TTL=253

192.168.88.50 からの応答: バイト数 =32 時間 =2ms TTL=253

192.168.88.50 の ping 統計:

    パケット数: 送信 = 4、受信 = 4、損失 = 0 (0% の損失)、

ラウンド トリップの概算時間 (ミリ秒):

    最小 = 2ms、最大 = 16ms、平均 = 5ms

1. Have you tried to reboot both switches and check if the LAG state shows Up?

I can only reboot Allied Telesis CentreCom GS908M. It is very difficult to reboot M7100-24X because it is in production in our company.

Best regards,