R6400v2 Installed firmware update which caused delays in connecting to websites or wouldn't connect at all. Tried logging onto the router to check the settings but it wouldn't connect to the router. Did a factory reset and the website connection problems went away but I still can't connect to the router itself. routerlogin.net says "refused to connect". 192.168.0.2 says "took too long to respond". I tried .1 and .0 with the same results. Please note: I am not even getting the router login screen. Any suggestions, please? Thanks

FYI. I the could not get the tftp method to work, but when the router reset I was able to log on and revert back to .91. I restored my config settings and everything works as it should. I am a little leary of retrying .95 for now. Still do not know why the web server ports were not open when I was running .95. Thank you all for your help and have a good safe new year.

you tried the default 192.168.1.1? Whats it connected to for gateway? Sometimes during setup it'll change its default if you're gateway is a modem/router combo device. Then it usually changes to the 10.0.0.1

Also have this problem after installing firmware V1.0.4.122_10.0.95.

DUIdui wrote: Also have this problem after installing firmware V1.0.4.122_10.0.95. Same question for you as the one from plemans . What is the modem/gateway (if there is one) in front of lour router.

Ah ha.. another log in porblem! Dougaday says:took too long to respond". I tried .1 and .0 with the same results. Please note: I am not even getting the router login screen. The modem should be on the WAN side and the login GUI is on the LAN side, so what does the modem have to do with the inablilty to log in to the web GUI on the LAN side? See more posts at:https://community.netgear.com/t5/General-WiFi-Routers-Non/V1-0-4-122-10-0-95-Update-on-R6400v2-kills-lon-in-page/m-p/2176066#M153300

R6400v2 Can't connect to the router itself

11 Replies

plemans
Guru
Dec 17, 2021
you tried the default 192.168.1.1?

Whats it connected to for gateway?

Sometimes during setup it'll change its default if you're gateway is a modem/router combo device. Then it usually changes to the 10.0.0.1
DUIdui
Aspirant
Dec 24, 2021
Also have this problem after installing firmware V1.0.4.122_10.0.95.
- michaelkenward
  Guru
  Dec 24, 2021
  DUIdui wrote:
  
  Also have this problem after installing firmware V1.0.4.122_10.0.95.
  
  Same question for you as the one from plemans .
  
  What is the modem/gateway (if there is one) in front of lour router.
  - Tvestra
    Star
    Dec 24, 2021
    Ah ha.. another log in porblem!
    
    Dougaday says:
    took too long to respond". I tried .1 and .0 with the same results. Please note: I am not even getting the router login screen.
    
    The modem should be on the WAN side and the login GUI is on the LAN side, so what does the modem have to do with the inablilty to log in to the web GUI on the LAN side?
    
    See more posts at:
    https://community.netgear.com/t5/General-WiFi-Routers-Non/V1-0-4-122-10-0-95-Update-on-R6400v2-kills-lon-in-page/m-p/2176066#M153300
ng_usa_user
Aspirant
Feb 06, 2022
after I installed V1.0.4.122_10.0.95, the webgui/http server was no longer responding.
I power cycled and webgui returned.

Forum Discussion

R6400v2 Can't connect to the router itself