NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
RogerFreeman
Dec 22, 2011Aspirant
NasMon v3.2 - cannot load one of the three pages.
Hello All
My installation of Nasmon v3.2 (http://www.readynas.com/forum/viewtopic.php?f=47&t=21184) is working, but one of its pages will not load. Why?
My ReadNAS Duo has the most recent image (from memory it was released in September 2011):
ReadyNAS Duo [X-RAID]
Firmware: RAIDiator 4.1.8 [1.00a043]
Memory: 256 MB [2.5-3-3-7]
IPv4 address:: 192.168.1.10
Volume C: Online, X-RAID, 2 disks, 61% of 925 GB used
Regarding Nasmon:
http://192.168.1.10/nasmon/phpsysinfo/index.php works OK
http://192.168.1.10/nasmon/nasinfo.php also loads and works OK
http://192.168.1.10/nasmon/ doesn't work OK - it just gets me a page which asks for an email address and password. Hitting "login" twice drops me to another page titled "loadAVG upgrade" , and a box therein saying "Upgrade complete. For security reasons, you should delete the install directory from your httpdocs folder". A button marked " go to graphs" takes me back to the page asking for the email&password info.
I've searched this forum and a few other online sources but not found an answer. I have carried out instruction as per elsewhere in this forum, but to no avail. Am I doing something stupid?
1) I've cleared my browser cache (Firefox, running on Linux) and rebooted the PC
2) I've rebooted ReadyNAS via its admin page
3) PHP (v1.1) is clearly installed and working as is Nasmon - but for the page where the graphs are.
4) It's been running for 4 or 5 hours now - OK on the first two pages but still no joy on the last URL mentioned.
5) The only other add-on is one which came preinstalled (I think) - ReadyNAS photos or similar name
What do I do next please, bearing in mind I am not a linux expert and don't have root access to the Duo? Thanks in advance for any guidance.
Roger Freeman
My installation of Nasmon v3.2 (http://www.readynas.com/forum/viewtopic.php?f=47&t=21184) is working, but one of its pages will not load. Why?
My ReadNAS Duo has the most recent image (from memory it was released in September 2011):
ReadyNAS Duo [X-RAID]
Firmware: RAIDiator 4.1.8 [1.00a043]
Memory: 256 MB [2.5-3-3-7]
IPv4 address:: 192.168.1.10
Volume C: Online, X-RAID, 2 disks, 61% of 925 GB used
Regarding Nasmon:
http://192.168.1.10/nasmon/phpsysinfo/index.php works OK
http://192.168.1.10/nasmon/nasinfo.php also loads and works OK
http://192.168.1.10/nasmon/ doesn't work OK - it just gets me a page which asks for an email address and password. Hitting "login" twice drops me to another page titled "loadAVG upgrade" , and a box therein saying "Upgrade complete. For security reasons, you should delete the install directory from your httpdocs folder". A button marked " go to graphs" takes me back to the page asking for the email&password info.
I've searched this forum and a few other online sources but not found an answer. I have carried out instruction as per elsewhere in this forum, but to no avail. Am I doing something stupid?
1) I've cleared my browser cache (Firefox, running on Linux) and rebooted the PC
2) I've rebooted ReadyNAS via its admin page
3) PHP (v1.1) is clearly installed and working as is Nasmon - but for the page where the graphs are.
4) It's been running for 4 or 5 hours now - OK on the first two pages but still no joy on the last URL mentioned.
5) The only other add-on is one which came preinstalled (I think) - ReadyNAS photos or similar name
What do I do next please, bearing in mind I am not a linux expert and don't have root access to the Duo? Thanks in advance for any guidance.
Roger Freeman
3 Replies
Replies have been turned off for this discussion
- viewtopic.php?f=61&t=50985
There were a few good bits of guidance from a couple of posters here... Have you seen this thread? viewtopic.php?f=61&t=50985 - RogerFreemanAspirantHello
Thanks for that URL - certainly useful and shows me where some of the problems might lie. I put the latest PHP on (v1.3) , just in case, but it didn't help.
However, it's a bit beyond me at the moment, to be editing scipts etc., because I don't know how to edit locations on the NASBox itself e.g.
/c/webroot/loadavg/phpsysinfo/includes/xml/class.SimpleXMLExtended.inc.php
Time for some web searches to see if I can discern how to get at the Nasbox - (presumably that means being root on it though, which means no more warranty). - RogerFreemanAspirantNo - beyond me. Programming, or at least scripting - all stuff I don't understand. I'd best uninstall and stop fiddling lest I break something
Related Content
NETGEAR Academy

Boost your skills with the Netgear Academy - Get trained, certified and stay ahead with the latest Netgear technology!
Join Us!