- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Re: Rif.: DC112A Failed to update GUI language file
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I'm currently using the DC112A with the WAN port connected to a satellite modem (high latency connection - ping time 600 - 700 ms)
Netgear Genie shows my current Firmware version is V1.0.0.32_1.0.60 and that a router firmware upgrade is available.
The Firmware Upgrade Assistant shows:
Current GUI Language Version: 1.0.0.32_2.1.38.3
New GUI Language Version: 1.0.0.44_2.1.38.3
Current Firmware Version 1.0.0.32
New Firmware Version 1.0.0.44_1.0.60
When I press the 'Yes' button I get the following two messages:
Downloading and updating the language table, please wait for approximately one minute...
and then
Failed to update GUI language file
-- Any ideas how to fix this?
Solved! Go to Solution.
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
All Replies
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: DC112A Failed to update GUI language file
Hi Bianca - that's fixed it: many thanks, Bob
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Rif.: DC112A Failed to update GUI language file
I tried to update the firmware.
It indicates that a new update is available. When I choose to update, it comes to the stage where it updates the language file and fails.
I tried also with genie sw (for window pc): it failed too.
Can you give us a link to the firmware file please?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Rif.: DC112A Failed to update GUI language file
Please see attachment with screenshots.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Rif.: DC112A Failed to update GUI language file
Hi, All,
May I please have the device SKU? It can be checked on their end by checking the box of the product, on the barcode label, which should indicate DC112A-xxxxxx.
Regards,
Blanca
Community Team
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Rif.: DC112A Failed to update GUI language file
Hi Blanca - mine is DC112A-1TLAUS - working well thanks
Bob
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Rif.: DC112A Failed to update GUI language file
Hi, All,
Thank you for providing your device's SKU. I am checking this with our engineers. I will provide update once new information will be available
Regards,
Blanca
Community Team
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: DC112A Failed to update GUI language file
Hello Everyone,
I'm also suffering the same problem...
A new version has been found. Do You want to upgrade to the new version now?
Current GUI Language Version: 1.0.0.18_2.1.38.3
New GUI Language Version: 1.0.0.44_2.1.38.3
Current Firmware Version 1.0.0.18
New Firmware Version 1.0.0.44_1.0.60
When I click YES, I get the GUI failure.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: DC112A Failed to update GUI language file
SKU: DC112A-100EUS
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: DC112A Failed to update GUI language file
DC112A-100EUS same issue never resolved, any advice?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: DC112A Failed to update GUI language file
Same problem
Current GUI Language Version: 1.0.0.18_2.1.38.3
New GUI Language Version: 1.0.0.44_2.1.38.3
Current Firmware Version 1.0.0.18
New Firmware Version 1.0.0.44_1.0.60
SKU: DC112A-100EUS
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: DC112A Failed to update GUI language file
@ab2019 wrote:Same problem
Current GUI Language Version: 1.0.0.18_2.1.38.3
New GUI Language Version: 1.0.0.44_2.1.38.3
Current Firmware Version 1.0.0.18
New Firmware Version 1.0.0.44_1.0.60
SKU: DC112A-100EUS
Some additinal weirdness, version reported below logout button:
Firmware Version
V1.0.0.18_1.0.60
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: DC112A Failed to update GUI language file
I have the same problem.
Customer service is NOT Netgear's strength.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Rif.: DC112A Failed to update GUI language file
Hi, All,
Engineering team provided the list of latest FW for DC112A:
DC112A-1TLAUS Latest FW is 1.0.0.42
DC112A-100EUS, DC112A-100NAS is 1.0.0.44
DC112A-1RDMES and DC112A-2RDMES for Oreedoo Latest FW is 1.0.0.42
DC112A-1Z1MES for Zain Latest FW is 1.0.0.42
Kindly check again if you already have the latest firmware.
Regards,
Blanca
Community Team
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Rif.: DC112A Failed to update GUI language file
You're kidding us now huh?
After a month's wait we will find out the latest FW for DC112A.
We have always known this - but since the language version does not work, we cannot update FW either.
Now you must solve this - we have all bought both a Smart Cradle Router and AirCard for very expensive money - but the support is under all criticism. There is not even a page to download the software manually. Shame on you!
Current UI language:
1.0.0.18_2.1.38.3
New user interface language:
1.0.0.44_2.1.38.3
Current version of firmware
1.0.0.34
New version of firmware
1.0.0.44_1.0.60
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Rif.: DC112A Failed to update GUI language file
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: DC112A Failed to update GUI language file
The fact that it will take over a month for your technicians to find a solution is not realistic and there is no real dialogue.
You have developed and sold the Smart Cradle, but you forgot the support somewhere along the way.
Visit the download center and enter "DC112A".
Firmware / Software: not available for this model.
Give us an answer now!
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: DC112A Failed to update GUI language file
It is now six days since the Netgear Moderator latest post...
We get no answers, so the question is whether Netgear wants the hardware in return?
The timeline with all the misleading answers from Netgear can only mean one thing - that it's hardware failure.
If there were only problems with the firmware, it would have been fixed a long time ago!
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: DC112A Failed to update GUI language file
Hello, I try many times to updrade to the new firmware and it is always the same message as you have, but in french and the upgrade failed with the same problem. I hope that Netgear will provide us a solution quickly now. May be if we have the new language pack and firmware we can upgrade by ourselves.
Version actuelle de la langue de l'interface graphique: 1.0.0.18_2.1.38.3
Nouvelle version de la langue de l'interface: 1.0.0.44_2.1.38.3
Version actuelle du micrologiciel (firmware) 1.0.0.34
Nouvelle version du micrologiciel (firmware) 1.0.0.44_1.0.60
Notes sur la version: 1. [Bug Fix] Fixed security issue. 2. [Bug Fix] Fixed security issue.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: DC112A Failed to update GUI language file
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: DC112A Failed to update GUI language file
i just cannot understand why they don't release the firmware to the download center so we can at least rule out a problem with delivery via the webUI. We were alerted to the security fixes in the firmware quite some time ago in a Netgear email campaign, and now they they have decided to actually push out what they said they did it doesn't even install.
I used to think Netgear's reputation was bulletproof from using their managed and smart switches, but now I'm not so sure.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Rif.: DC112A Failed to update GUI language file
Hi, All,
I have raised this issue several times to our engineering team. There are only few users who managed to get the firmware updated but majority are still having issue. And this is being investigated. We are now considering of posting the firmware on our support site. You may also send me a private message with the device SKU (DC112A-xxx) and I'll check with them if I can provide the firmware.
I apologize for the inconvenience this has all caused you and appreciate the patience.
Regards,
Blanca
Community Team
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more