- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Re: D6400 wont upgrade to the 1.0.0.88
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Currently my d6400 is on V1.0.0.86 and the web interface say it is a new version available v1.0.0.88 I click yes, it starts downloading, installing...rebooting and than after a login, i see again V1.0.0.86
Do they test they work before they release?
Do i habe to do it manually? Anybody tried?
Thank you
Solved! Go to Solution.
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I had the same problem... did it through the Netgear Genie page using both the "update firmware" button at top of page, and through the Advanced- router update menu options on the LH side of page. Seemed to be downloading with 'petrol gauge' bar moving (took about 2 mins to completed) but the icon on the page carried on rotating for 30 mins with no action, so I logged off. I then tried the other way suggested on this forum. I downloaded v1.0.0.188.chk from the Netgear website on to desktop then opened the Netgear Genie menu page again, opened 'Advanced" then "Administration" then 'Router update" . Clicked the 'Browse" button to locate upgrade file from desktop and pressed "upload' and Voila! it worked! All went a bit blank but when I logged on again to Netgear to check, the new upgrade was shown. Hope this helps others.
All Replies
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: D6400 wont upgrade to the 1.0.0.88
> Do they test they work before they release?
Evidence for that is sparse.
> Do i habe to do it manually? [...]
If I had a D6400, then I'd try that.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: D6400 wont upgrade to the 1.0.0.88
I had the same problem...Had to download and manually upgrade.
Kinda wish I hadn't as the router has been a bit buggy since then!
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: D6400 wont upgrade to the 1.0.0.88
What kind of iisues do you have?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: D6400 wont upgrade to the 1.0.0.88
The router becomes unresponsive and I'll have to power it off and back on again...I should probably factory reset, but I haven't had time to yet... 😕
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: D6400 wont upgrade to the 1.0.0.88
> The router becomes unresponsive [...]
"unresponsive" to _what_? LED indicators freeze? Management web
site dies? Some part of Internet access fails (when you try some
specific action)? Other?
"unresponsive" is not a very useful problem description. It does not
say what you did. It does not say what happened when you did it. As
usual, showing actual actions with their actual results (error messages,
LED indicators, ...) can be more helpful than vague descriptions or
interpretations.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: D6400 wont upgrade to the 1.0.0.88
Had I been the OP, looking for help, I may have given a full description.
As it stands, it was just an off the cuff remark.
But seeing as you asked, unresponsive means that the internet drops and if you log into it, the UI doesn't respond / fully load.
As mentioned previously, when I have time, I'll probably reset the unit...
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: D6400 wont upgrade to the 1.0.0.88
> [...] unresponsive means that the internet drops and if you log into
> it, the UI doesn't respond / fully load.
Not a big improvement. Does "the internet drops" mean a DNS failure,
or a general communication failure, or what? LEDs? See "As usual,
[...]", above. If the router is "unresponsive", then how can "you log
into it"? Is there an actual error message associated with "the UI
doesn't respond"? What does "[not] fully load" mean?
> As it stands, it was just an off the cuff remark.
As it stands, it's approximately useless as a problem description.
See "is not a very useful problem description [...]", above. Are you
trying to convey vague unhappiness, or useful information about your
problem?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: D6400 wont upgrade to the 1.0.0.88
\Face Palm/
I don't need your help.
It was remark, not a cry for help, so you can simmer down now.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: D6400 wont upgrade to the 1.0.0.88
@MoodyB wrote:
Kinda wish I hadn't as the router has been a bit buggy since then!
Did you reset the router to factory settings after the firmware flash?
New firmware sometimes introduces changes that are not compatible with the old configuration.
So while it isn't guaranteed to fix problems a factory reset is the first thing to try if you have issues with new firmware.
This is a nuisance because you then have to reconfigure the device all over again.
You can backup your settings before you reset and restore them later. But that may just bring back the fault. Then again, at least you will know if the reset fixed the problem.
I did the manual update yesterday. I confess that the thing is just sitting there waiting for me to try it on my second line. (I switched to a DM200 + R7800 combination.) So I can't say of there are bugs in the new version.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: D6400 wont upgrade to the 1.0.0.88
MoodyB...
i get the EXACT same thing as you mentioned. constant drops, thought it was our internet but when it drops i cannot log into the router either.
so im always excited for an update to the firmware that never really fixes anything. and now here i am cant even update to .88
goin manual style...
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I had the same problem... did it through the Netgear Genie page using both the "update firmware" button at top of page, and through the Advanced- router update menu options on the LH side of page. Seemed to be downloading with 'petrol gauge' bar moving (took about 2 mins to completed) but the icon on the page carried on rotating for 30 mins with no action, so I logged off. I then tried the other way suggested on this forum. I downloaded v1.0.0.188.chk from the Netgear website on to desktop then opened the Netgear Genie menu page again, opened 'Advanced" then "Administration" then 'Router update" . Clicked the 'Browse" button to locate upgrade file from desktop and pressed "upload' and Voila! it worked! All went a bit blank but when I logged on again to Netgear to check, the new upgrade was shown. Hope this helps others.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: D6400 wont upgrade to the 1.0.0.88
Basically upgrade manually.
• Introducing NETGEAR WiFi 7 Orbi 770 Series and Nighthawk RS300
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more