- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Re: FW 2.1.1.16 Update broken backhaul
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
FW 2.1.1.16 Update broken backhaul
The update from 2.1.1.12 to 2.1.1.16 has reduced backhaul status to POOR from GOOD; not what you like to see really
Sysyem configuration and positioning unchanged, tried both a reboot and resync still have a POOR Status on the backhaul.
System seems to work finein spite of this but link to satelitte slow to establish.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: FW 2.1.1.16 Update broken backhaul
Update:
Unticking the Enable Daisy-Chain Topology box (which had been enabled as default in earlier firmware) restored the link status to GOOD!
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: FW 2.1.1.16 Update broken backhaul
Honestly! Why do the latest firmware releases have that box checked by default? Sheesh!!
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: FW 2.1.1.16 Update broken backhaul
Hi,
Had exactly the same thing when updating the firmware to v 2.1.1.16.
Do we need or not to enable the daisy chain connection?
Don't like to have the satellite backhaul status to "poor"...
Thanks
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: FW 2.1.1.16 Update broken backhaul
If you only have one satellite, there's no point to enabling Daisy Chain. Leave it disabled.
If you have more than one satellite, but they are arranged in a hub-&-spoke manner aorund the router (i.e. S-R-S), then there is still no point in enabling Daisy Chain. Leave it disabled.
If you have multiple sats, but they need to talk to each other (i.e. R-S-S), then do enable Daisy Chain - that's the scenario it's deisgned to support.
I only have on sat, so I myself can't speak to how effective Daisy Chain acutally works.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: FW 2.1.1.16 Update broken backhaul
I have the same issue after my router updated to 2.1.1.16. Poor connection status on the satellite and it's connecting at 2.4Ghz instead of 5Ghz.
So I logged into the satellite and noticed it still had to old firmware version installed on it. So the "auto update" didn't seem to apply to the satellite. Looks like poor QA on this one.
I manually updated the firmware on the satellite and it's now connecting properly at 5Ghz. The only issue I still see is the satellite reports no connection back to the base but the base reports a good connection to the satellite. I did see the blue connection light so I think it's working.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: FW 2.1.1.16 Update broken backhaul
After 30 minutes, my satellite now shows as connected at 5Ghz. So in my case updating the firmware on the satellite (and resynching them using the buttons on the back of each) resolved the issue.
I left the daily chaining on in case I decide to add another satellite to the system.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: FW 2.1.1.16 Update broken backhaul
I see some folks have firmware version 2.1.1.16
My RBK53 (AKA RBR50) is showing version 2.0.0.74, same for my two satellites.
Status states 'no new firmware version available'
What changes to the backhaul were made? How can I get latest version?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: FW 2.1.1.16 Update broken backhaul
how can 2.1.2.18 be classed as older than 2.0.1.4 on the website and yet the orbi says its older how on earth does that make sense.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: FW 2.1.1.16 Update broken backhaul
v.18 was removed from being current version due to user complaints. NG now recommends using v2.0.1.4 is the most currnet version.
If your not having issues with your system, keep whats loaded on it. If your using v18 and having uses, NG recommend reverting back to v2.0.1.4.
Hopefully new update will be soon:
@Pedro_mustardwrote:how can 2.1.2.18 be classed as older than 2.0.1.4 on the website and yet the orbi says its older how on earth does that make sense.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: FW 2.1.1.16 Update broken backhaul
Thanks for that very interesting Backhaul I'm having an issue with myself so the revised update will be interesting.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: FW 2.1.1.16 Update broken backhaul
You might ask NG support if you could try a beta if ones available. You'll have to phone contact them to ask.
LAN backhaul is working for me. I persume it will be in next update.
• Introducing NETGEAR WiFi 7 Orbi 770 Series and Nighthawk RS300
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more