NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Nighthawk M1 - selection of LTE Frequency/Band
Hello there, is there any way to select the LTE Band/Frequency the router should log on to? This would really help to avoid switching from a "good" cell to a bad one. With Huawei Routers I can do that using a third party tool. (LTE Watch). Unfortunately this is not available for Netgear Routers. Thanks for your comments!Nighthawk M1 IP addresses - allow both dynamic and static
The Nighthawk M1 network IP address setup currently allows either dynamic DHCP address assignment within a specified range or fully manual assignment of static IP addresses to wired or WiFi connected devices. However, it's not currently possible to enable DHCP addressing within a specified range together with some additional manually specified static IP addresses. This is a problem where some devices in the network need static addresses, such as printers, but where automated dynamic addressing is needed for "visiting" devices on the network. I currently have DHCP enabled in my M1 but this means that when my networked printer is powered up it's often allocated a different IP address, so to print from a networked PC I first have to access the browser interface to the M1 to find the IP address and then go into the PC's control panel to modify the address in the printer port setting. Could the firmware / interface be modified so that DHCP can be enabled but at the same time allow some static IP addresses to be specified for printers, etc. so that they can always be located by other networked devices? If anyone else feels this would be a beneficial feature, please add your comments. The mobile network provider that supplied the M1 to me is EE in the UK (there's no option to specify MR1100EE¦Nighthawk LTE Mobile Hotspot Router (UK) in this post) but I guess that the US and Australian firmware also has this "either/or" limitation with the dynamic and static IP addressing.M1 (MR1100) needs battery to update firmware
My suspicions expressed at the end of this post seem to be confirmed - apparently you currently need a battery installed in the M1 in order to update its firmware. If this is correct, it's a big problem for people running their M1 solely on the mains charger, especially if the M1 is in a remote, difficult-to-access location. I believe the firmware needs to be changed so that if the M1 is being run without a battery, using a sufficiently powerful mains charger (see the link in the next paragraph) then firmware auto-upgrades should be allowed to proceed. If you agree with this proposal, please hit the Kudos button - it may draw attention to this post. I'm using my Nighthawk M1 (MR1100) without its battery, powered only by an upgraded mains charger for 24/7 internet access at home. This morning I found I had no internet connection and the LED on the M1 was flashing orange rapidly but dully. I decided just to turn off the power, wait a few seconds and then turn it back on. This probably wasn't a good idea - it would have been better to try to shut it down by holding the M1's power button in until it shut itself down "gracefully" - I guess I could have "bricked" the M1 if it had been in the middle of a firmware update. Anyway, after powering back up, thankfully the LCD screen then displayed a progress bar and a message similar to "Updating - do not power off". The progress bar moved fairly rapidly but when it reached 100%, the LCD screen went blank and the orange LED started flashing rapidly again. I'd noticed previously that in the web-based interface under Settings > Adminstration > Firmware Update, there was an advisory note saying "Software Update unavailable when battery level is below 20%", so I suspected that running the M1 without a battery might cause issues when it tried to auto-update the firmware. I inserted the battery (already charged to around 70%) without turning off the mains charger and the LCD screen again displayed the progress bar with the warning not to power off. This time, the progress bar didn't move smoothly to 100%, it jumped in stages and each time the LCD screen went blank for a while. When it reached 100%, the M1 appeared to reboot, possibly more than once, but eventually the normal LCD display returned and the LED was flashing blue as ususal. When I checked the web-based interface, there was a message stating that the software had been updated successfully. Prior to the update, my M1 was on firmware version NTG9X50C_10.20.05.00. It's now on NTG9X50C_10.22.03.00, which has a build date of 22nd Nov 2017. I'm in the UK and my provider is EE - it's possible that the firmware version numbers differ from country to country. I've no idea what has changed in this firmware version - on a quick glance through the interface, I don't see any new options so I guess the changes were bug fixes. Unfortunately, there's no new option to stop the Ethernet port going to sleep when running on the mains charger without a battery. However, this feature wasn't promised until Feb. It would be very useful if Netgear published a firmware update history on their site, even though they are not providing the firmware itself for downloading. At least we could then see what had changed. If you agree with me on this point, I ask you again to hit the Kudos button. Thanks.Wie nutze ich den Nighthawk M1 als Arlo Basisstation?
Hallo Achtung kann korrektes Modell nicht eingeben. Es handelt sich hier um das Modell Nighthawk M1 MR1100-100. Laut Beschrieb unterstützt der Nighthawk das intelligente Arlo Heimsicherheitssystem als Basisstation für Arlo Kameras. http://www.netgear.ch/home/products/mobile-broadband/mobilerouters/M1.aspx Wie muss ich diese Funktion aktivieren? Wie kann ich meine Arlo Kameras mit dem Nighthawk M1 verbinden? in der Netgear Mobile App und auch in der Bedienungsanleitung zum Nighthawk M1 finde ich nichts zu Arlo. Danke für Eure Hilfe
Netgear Nighthawk M1 drops LTe connection every day and requires multiple reboots
Hi there, Purchased a Nighthawk M1 (MR1100) from Telstra recently. Seems to work well in terms of speed. But a few problems including severe lack of configuration for DHCP (the only item you can configure is DHCP range - there's no fixed host mappings, or any even basic features present in almost every other device on the market. I really hope this is addressed in a future patch or Netgear advise a secret menu to access these basic features as it's really disappointing and lets the router down at the present time). However, it's by far the fastest I've ever tested. Anyway to the main problem. Every day when I come home the device is no longer providing Internet over the connected ethernet cable. I can connect to the modem admin screen fine, and it reports it's connected to the internet (reports LTE connection is fine and has been connected for over a day); however, no devices on the network can use the internet and the only way to solve it is by restarting the MR1100 multiple times eventually it starts routing traffic again. This problem does not occur on any of the other modems I've tested using the same SIM/Service so it's definitely an issue with the MR1100. Something is wrong with the software - need someone from Netgear to sort this out. Also Netgear you need to add the Nighthawk M1 to your model list as I had to assign this ticket against a random unrelated modem as your product list isn't up to date.