NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
New - R7000 Firmware Version 1.0.11.136 Released
Bug Fixes: 07/29/2022
- Fixes the issue where DHCP reservation can only support 62 addresses.
NOTE: IF DNS issues are seen with this version of FW, please enable IPv6 protocols on the router.
Download Link:
https://www.netgear.com/support/product/r7000.aspx
Firmware Update Instructions:
To update your router’s firmware, follow the instructions in your router’s user manual. To view your router’s user manual, visit https://www.netgear.com/support/product/R7000.aspx#docs.
Manually update FW on the router if this isn't seen on the routers web page:
https://kb.netgear.com/23960/How-do-I-manually-update-the-firmware-on-my-NETGEAR-router
NOTE: Use a wired PC and web browser to update router FW. If continued problems are seen after a FW update, it's recommended to try a factory reset and setup from scratch with out loading any saved configurations from backup files.
This article applies to:
Let us know how this version of FW works for you...
14 Replies
Replies have been turned off for this discussion
just like previous version, it only stayed connected for several hours then stopped connection. this bug that exists in all version later than 42 has never been fixed.
What is the Mfr and model# of the Internet Service Providers modem/ONT the NG router is connected too?
What was the LED indication on the top of the router when this happened?
What CAT# lan cable are you using between the modem and router?
What devices do you have all connected?
Has a power off for 1 minute then back ON with the ISP modem and router been performed since last update?
Be sure to restart your network in this sequence:
Turn off and unplug modem.
Turn off router and computers.
Plug in and turn on modem. Wait 2 minutes for it to connect.
Turn on the router and wait 2 minutes for it to connect.
Turn on computers and rest of network.Has a factory reset and setup from scratch been performed since last FW update?
I didn't see this with mine:
i use r7000 as 5GHz AP.
- This may sound crazy but I was having the dropping problem . I went back to my old firmware because of the dropping wifi issues. The next day I tried .136 again and then I installed it a second time right over the top of the first one immediately and everything works. I had tried .136 three times previously with bad results.
Only this I am having a issue with now is that I can't install the nighthawk app on my cell because of a timeout message but my r7000 has been working flawlessly for 3 days.Has a factory reset and setup from scratch been performed since last FW update? This is recommended if you run into any problems after updating FW.
What is the Mfr and model# of the Internet Service Providers modem/ONT the NG router is connected too?
For any NH app problems, please post here:
https://community.netgear.com/t5/Nighthawk-App/bd-p/en-home-networking-apps
Greg007 wrote:
This may sound crazy but I was having the dropping problem . I went back to my old firmware because of the dropping wifi issues. The next day I tried .136 again and then I installed it a second time right over the top of the first one immediately and everything works. I had tried .136 three times previously with bad results.
Only this I am having a issue with now is that I can't install the nighthawk app on my cell because of a timeout message but my r7000 has been working flawlessly for 3 days.
Hello,
By chance checking again for new firmware. The R7000's are still on stable but likely vulnerable V1.0.9.42_10.2.44.
Tried some upgrades in the past, but all were a failure in stability specific throughput and WIFI. Hence I gave up. WIth the feedback again here on the forum. Not really an incentive to do the upgrade hassle over again. Waiting to maybe ever ever hear about a golden version that simply works good and reliable.
Have all a good and healthy 2023, Bas.I think v.124 was a good version. Didn't see any issues with it.
Also other factor to consider about FW versions and troubleshooting problems.
Not everything if FW caused.
Hi all,
Is the this 1.0.11.136 Released the last firmware for the R7000?
Also is the R7000 end of life?Currently im running Firmware Version
V1.0.11.128_10.2.112 and its smooth. But ofcourse I want the latest firmware to feature proof.Most likely last update.
Hot54321 wrote:
Also is the R7000 end of life?
I cant find the R7000 in the spreadsheet: https://downloads1.netgear.com/files/netgear/documents/SMB_EOL_Product_List_Sep2023.pdf
CTRL+F :R7000 or 7000 = zero hits / 0 hits, its not listed there.
