- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
VLAN 1 not editable?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I have a GS724T, V5.2.0.11. I'm trying to remove VLAN 1, and it says "VLAN 1 not editable". I was able to remove VLAN 1 from proSAFE XS716T and XS728T.
Any idea why?
Solved! Go to Solution.
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
@tantony wrote:
Correct. This switch does not show up in the SCC. The ProSAFE switches does.
ProSafe is or was just a marketing name for the Smart Managed Pro switch line - based on earlier posts these are XS7xxT, OK.
@tantony wrote:
I have a GS724T, V5.2.0.11.
Sorry, correction. I have a GS724TPv2, and that one shows up in the SCC. This switch is less than one month old.
That GS724TPv2 is the new one you talked of, and theere is still a GS724T with a v5.2.0.11 firmware which can't be discovered by SCC? If yes, this switch requires an update. Still, best guess is that this was some factory firmware, I can't even find the .11 in the GS724T v3 (that's a hardware version - product designation sometjing like GS724T-300NAS) downloads.
GS716Tv2 & GS724Tv3 Firmware Version 5.0.2.14 dates from summer 2012... see https://www.netgear.com/support/product/GS724Tv3#download -> previous versions
All Replies
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: VLAN 1 not editable?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: VLAN 1 not editable?
Is that the reason why its not showing up on the SmartControlCenter and the ProSAFE switches do? All 3 switches are on the same subnet / VLAN.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: VLAN 1 not editable?
@tantony wrote:
Is that the reason why its not showing up on the SmartControlCenter and the ProSAFE switches do? All 3 switches are on the same subnet / VLAN.
Forget the marekting names - the GS724T (v3?) does not show up?
@tantony wrote:
I have a GS724T, V5.2.0.11.
This reads like a GS724T v3 model (v1 and v2 use much lover firmware series) - requiring an update https://www.netgear.com/support/product/GS724Tv3#download
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: VLAN 1 not editable?
Forget the marekting names - the GS724T (v3?) does not show up?
Correct. This switch does not show up in the SCC. The ProSAFE switches does.
I have a GS724T, V5.2.0.11.
Sorry, correction. I have a GS724TPv2, and that one shows up in the SCC. This switch is less than one month old.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
@tantony wrote:
Correct. This switch does not show up in the SCC. The ProSAFE switches does.
ProSafe is or was just a marketing name for the Smart Managed Pro switch line - based on earlier posts these are XS7xxT, OK.
@tantony wrote:
I have a GS724T, V5.2.0.11.
Sorry, correction. I have a GS724TPv2, and that one shows up in the SCC. This switch is less than one month old.
That GS724TPv2 is the new one you talked of, and theere is still a GS724T with a v5.2.0.11 firmware which can't be discovered by SCC? If yes, this switch requires an update. Still, best guess is that this was some factory firmware, I can't even find the .11 in the GS724T v3 (that's a hardware version - product designation sometjing like GS724T-300NAS) downloads.
GS716Tv2 & GS724Tv3 Firmware Version 5.0.2.14 dates from summer 2012... see https://www.netgear.com/support/product/GS724Tv3#download -> previous versions