Search the Community
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
158 results
Sorted by:
2024-01-18
08:03 AM
Just wondering if the WAN port on my Netgear DGND3700-NAS100 N600 DSL modem/router could be used with Starlink V2 (with its Ethernet adapter) . I have been using the DGND3700 for years w...
2023-06-07
06:41 AM
I followed with interest the (now locked) discussion at https://community.netgear.com/t5/Orbi-WIFI-6-AX-AND-Wi-Fi-6E-AXE/Orbi-6e-cannot-connect-to-Starlink/td-p/2223240/page/2 and being somewhat d...
Show results in replies (6)
-
...able. Don't connect the StarLink adapter to the switch just yet. Power ON the RBR and switch. The S...
-
...ommon modems and ONTs with out the need of any cross over connection. The issue seems to be with Starlink...
-
...ort and Starlink V1 AUX port fails to show link LEDs on the Orbi side. If the Orbi cable is moved to t...
-
Yes, I accept that it may very well be oversight on the Starlink hardware design side, and the T-5...
-
...easure of extra patience before I plugged the Starlink into the switch. The Safari browser on my i...
-
...ill address the issue because my Orbi is connected to a Spectrum modem rather than Starlink. p.s. T...
2023-11-28
02:45 AM
I have just got Starlink and can connect wirelessly to it fine. I can put it in bypass mode, plug a 2m ethernet cable into the adaptor and connect this to my Netgear 4 - Stream AX1800 WiFi 6 R...
Show results in replies (9)
-
SOLVED! I put a switch in between the Starlink ethernet adapter and the cat cable which runs up t...
-
Thanks for your quick reply. Re your first question, the “it” in bypass mode is the Starlink r...
-
...bigger network with multiple Internet addresses, the Starlink Modem in bridge mode can does a...
-
Thanks, I’m already using the Starlink ethernet adapter as noted previously (otherwise there’d be n...
-
@J27 wrote: Re your 2nd question, the adapter is the Starlink ethernet adapter you can p...
-
...ouse. The cat5a cable goes from my barn (where Starlink and adapter are) underground to my house. A...
-
Yes Starlink adapter is just one in one out. No switch being used here. Router is Nighthawk A...
-
@J27 wrote: I have just got Starlink and can connect wirelessly to it fine. I can put it in b...
-
An update!! The cat5a cable in wuestion which runs from the Starlink adapter in my barn to my h...
2022-05-13
10:06 PM
2 Kudos
Well I wasn't able to get the Orbi 960 to get an Internet connection with Starlink V2, using the Starlink Ethernet adapter, so have filed a trouble ticket with Netgear. The unit is getting an IP a...
Show results in replies (9)
-
I just purchased the orbi 6e and tried to get ot to work with my starlink gen2 and had the same e...
-
I have the Starlink V2 (rectangular version 2) system, and recently installed the Starlink E...
-
Awesome. Thank you!
-
Hi Mikey @Mikey94025 , Yes, the laptop connection Ethernet to Starlink V2. works just f...
-
...ox plugged in power and the cat6 cable from the starlink adapter into it and from the output on the s...
-
This is a generic picture from the internet of the adapter. I'm not certain what it is rated at or ...
-
...unior0415 wrote: I just purchased the orbi 6e and tried to get ot to work with my starlink gen2 a...
-
Even trying the Static Route configuration that was mentioned?
-
What type of netgear gs108t switch did you get? I see a few different versions. Also, d...
2022-09-25
10:29 AM
I'm new to starlink and saw references to set up static routing, so tried it. i've got a gen 2 dishy and operate with the internet adapter and starlink in pass through mode. for me the statistic t...
2022-07-06
10:16 AM
1 Kudo
2022-07-06
10:16 AM
1 Kudo
I cannot get my new AX1800 router to connect to the internet through Starlink. I have plugged and unplugged it all. Still no internet. Any suggestions before I return the router? Thanks for your h...
Show results in replies (5)
-
Thanks for your help. I got it to work by bypassing the Starlink Router. LOL - this is not for t...
-
What router is it from starlink?
-
...en 2 Starlink goes directly into the Ethernet port on the back of the main AX1800 router. When I’m t...
-
...bsp; Try putting the netgear in access point mode and then connecting it to the starlink router.
-
Either way glad you got it working! Starlink does make it a bit of challenge as they're wanting t...
2022-06-02
04:52 PM
So I have the round Starlink dish. I replaced the router with a Netgear one so that I could link to a mesh (AC1900 WiFi Mesh Extender Nighthawk® Dual-band WiFi Mesh Extender), but I just cannot get m...
2022-10-22
04:55 PM
Good morning, people. I have a problem that I cannot work out... I live in rural NSW, Australia, and have set up a Starlink System on our farm. due to the trees, we have found it necessary t...
Labels:
2021-02-18
12:50 PM
I have a Netgear Nighthawk RAX70 connected to the Starlink dish (instead of the provided router which, if I can get this working, isn't necessary.) Others have been successful using their own r...
2022-08-15
08:26 AM
I have a Starlink connection with the router in bypass mode. I am using a Nighthawk as DNS and DHCP server for the network. I have a requirement of a LAN base address of 192.168.100.x with a couple o...
Show results in replies (4)
-
We can't put the Starlink router in router mode because it is a dumb router and can't do fixed IP a...
-
R7000P. The Starlink is in bypass mode so we are getting a WAN address from their gateway. The p...
-
...o is put the Starlink into router mode then put the R7000P in router mode into Startlinks DMZ. C...
-
Something that can't be done on the NH router. It has to use something other than 192.168.100.x Tha...