- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
R7000 DHCP question
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
R7000 DHCP question
I checked my R7000 log this morning and saw this:
"[LAN access from remote] from 192.144.226.157:26559 to 192.168.1.2:80, Tuesday, Jun 28,2022 03:33:38"
Reading through the logs I see multiple entries like this with different IP address all "to 192.168.1.2"
I have DHCP turned on and the range begins at 192.168.1.2.
I have a list of devices that are Allowed and 192.168.1.2 is not one them.
Is this a problem I should be concerned about?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7000 DHCP question
Do a who is lookup on 192.144.226.157
What FW version is currently loaded?
What is the Mfr and model# of the Internet Service Providers modem/ONT the NG router is connected too?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7000 DHCP question
Thanks for the reply.
Netgear FW: V1.0.9.88_10.2.88
I looked up a couple of the IPs and they were an ISP in England - pptechnology.
Modem: Motorola Surfboard SB6120 connected to Comcast.
Also noticed they're all connecting to 192.168.1.2:80 (port 80 - the HTTP port).
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7000 DHCP question
Gotta step out for a couple hours. I'll check in when I get back.
Thanks again.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7000 DHCP question
What devices has the address 192.168.1.2?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7000 DHCP question
I did a little more digging in the logs. Here are a few examples:
[LAN access from remote] from 2.57.122.209:17773 to 192.168.1.2:80, Monday, Jun 27,2022 07:37:33 PPTECHNOLOGY LIMITED
[LAN access from remote] from 185.196.220.70:50551 to 192.168.1.2:80, Monday, Jun 27,2022 07:10:34 = HOSTLICK - Germany (AbuseIPDB: This IP was reported 1,076 times. Confidence of Abuse is 12%)
[LAN access from remote] from 221.176.116.78:20647 to 192.168.1.2:80, Monday, Jun 27,2022 07:09:36 = China Mobile Communications Corporation - ISP (AbuseIPDB: This IP was reported 663 times. Confidence of Abuse is 100%)
[LAN access from remote] from 154.89.5.87:58914 to 192.168.1.2:80, Monday, Jun 27,2022 06:39:43 = AgotoZ HK Limited (AbuseIPDB: This IP was reported 1,132 times. Confidence of Abuse is 100%)
[LAN access from remote] from 128.1.248.46:18057 to 192.168.1.2:80, Monday, Jun 27,2022 06:35:25 = Zenlayer Inc (AbuseIPDB: This IP was reported 14,921 times. Confidence of Abuse is 100%)
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7000 DHCP question
That's just it. . . none of them. I pinged the address and get no reply messages.
It's not listed in my "Connected Devices" page in the Netgear software either.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7000 DHCP question
Would be curious to see what happens if you set the default DHCP IP address range to 192.168.1.100 to.200.
Has a factory reset and setup from scratch been performed since you updated FW?
Something would be using .2 I believe. What browser are you using? Try MS Edge or Firefox and see what's seen in Connected Devices.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7000 DHCP question
Pinging 192.168.1.2 with 32 bytes of data
Reply from 192.168.1.100: Destination host unreachable.
Reply from 192.168.1.100: Destination host unreachable.
Reply from 192.168.1.100: Destination host unreachable.
Reply from 192.168.1.100: Destination host unreachable.
Ping statistics for 192.168.1.2:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7000 DHCP question
I would do this, turn OFF all devices accept for 1 wired PC. Change the Default DHCP IP address pool range as suggested.
After you apply the change and the router reboot. Power OFF the ISP modem and router for 1 minute then back ON.
I would leave all devices off accept for the 1 wired PC.
Check the connected devices page on the router. You PC should be listed here.
If it is, turn on 1 device. Let it connect, check the connected devices list again. If seen, check the log page for any LAN access entries.
Graduate turning on devices one at a time and check the connected devices page. Take not of any device that doesn't appear on the page.
Check the log for any continue LAN access entries.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7000 DHCP question
Earlier today I reset DHCP to begin range with 192.168.1.3.
I cleared the logs and will post when there are some entries.
[LAN access from remote] from 163.172.158.4:57501 to 192.168.1.2:80, Tuesday, Jun 28,2022 10:02:50
BUT, I just remembered I used to host a web server. I searched some code that checked on the IP of the server and it was 192.168.1.2. Took it offline years ago and it's not even connected.
Thoughts?
• Introducing NETGEAR WiFi 7 Orbi 770 Series and Nighthawk RS300
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more