This topic has been marked solved and closed to new posts due to inactivity. We hope you'll join the conversation by posting to an open topic or starting a new one.
Re: ReadyNAS Ultra 6 Review (RNDU6000) no network activity???
I did what is in the manual. Via putty with telnet but no connection.
I tried to boot the NAS again but it is not booting any more. So, I dont know what happend??? Only seeing READY NAS. And RAIDar can not find the NAS either. Even without disks it is not booting.
Re: ReadyNAS Ultra 6 Review (RNDU6000) no network activity???
Sadly, this is sounding more and more like a hardware issue and you just got lucky when it booted a few times. Are you back to seeing no Ethernet activity? Try turning it off for an extended period and re-boot.
Re: ReadyNAS Ultra 6 Review (RNDU6000) no network activity???
Did you ever get it to boot past "ReadyNAS" on the display with the new memory? If not, it could be either the memory itself or something that came loose when you added it. It's not the drives initializing. Even though access can be a bit slow, your NAS is still accessible during volume initialization.
Re: ReadyNAS Ultra 6 Review (RNDU6000) no network activity???
With the new memory banks it was just working fine. Boot a several times and it was accessible. After trying to get in support tech modus it was till working fine. Just when I was to try again and check Putty is via telnet and not SSH, I pushed twice for shutting down. After that is was not booting again. I tried also with the old memory bank but still the same. Not booting, no internet led`s and not accessible. So it is not booting. With disks or without disks. With new memory or old memory.
Re: ReadyNAS Ultra 6 Review (RNDU6000) no network activity???
And the display just says "ReadyNAS"? Could be flash memory corruption, for which a USB recovery is the solution. Did you successfully back up the VPD file? Since USB recovery re-writes the flash where the VPD is located, corruption of it is possible (though it's supposed to be protected).
Re: ReadyNAS Ultra 6 Review (RNDU6000) no network activity???
The display will show "ReadyNAS" with nothing present except 5V, so there are many possibilities.
Sounds like time to try USB recovery. You never got to the point of installing OS6, right? So, a standard OS4.2.31 recovery is called for. It could be the power supply or something else (lots of re-booting can stress an old PSU and other components). If the USB recovery doesn't work, then further investigation is best performed by first installing a VGA cable and monitor onto the VGA header located on the motherboard and seeing if it's even getting through motherboard POST.
Re: ReadyNAS Ultra 6 Review (RNDU6000) no network activity???
Looking back through the thread, it does not appear you ever properly tried another power supply. A failing PSU was was one of my early suspicions. I've never tried to connect just the 24-pin connector, as you apparently did, I think you must also power the SATA backplane. I absolutely know that you cannot leave the original PSU connected to the backplane and expect it to work with a different supply on the 24-pin. If the ATX power supply you tried has no 4-pin Molex connectors, then you'll need some SATA to Molex adapters. With no drives installed, just for testing, you should only need to connect one of the three.
Then again, with your data now all backed up, you may want to take this as a sign it's time to move on to another NAS.
Re: ReadyNAS Ultra 6 Review (RNDU6000) no network activity???
hello, I have the same problem after the update I managed to restart my nas but the VPD is corrupted. what to do? I just want to give it a sledgehammer blow. I hope to find some help on this forum. Thanks
Re: ReadyNAS Ultra 6 Review (RNDU6000) no network activity???
You should not "tack on" to other message chains, especially those with different symptoms from yours. Is your NAS also an RNDU6000? How have you reached the conclusion your VPD is corrupt?
