- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Re: ReadyNASOS 6.5.0 (RC2) Shows UPS Warning after Installation
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
After installing 6.5.0 (RC2) I get a device status of UPS Warning.
I never had this with the prior release.
Is there something I need to do to clear this warning?
Solved! Go to Solution.
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Installed 6.5.0 RC3 and the UPS is detected again, just like before.
Thanks for getting the fix in.
All Replies
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: ReadyNASOS 6.5.0 (RC2) Shows UPS Warning after Installation
I had that briefly on the overview after upgrade also, but went into UPS settings, saw it was recognised there OK (green), and returned to the overview and it was then showing as OK (green). For me, the NAS no doubt just needed time to recognise it.
But that probably doesn't help you...
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: ReadyNASOS 6.5.0 (RC2) Shows UPS Warning after Installation
It looks as if the UPS is no longer auto detected by the NAS.
I am using an APC NS1250 UPS.
In the NAS menu, I select System, Power, UPS.
I then see the screen as shown below:
The unit is attached to the Left Rear USB port.
What am I supposed to enter for Address?
Any help would be appreciated.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: ReadyNASOS 6.5.0 (RC2) Shows UPS Warning after Installation
You can't manually add a USB-connected NAS. Both SNMP and Remote UPS options are for monitoring the UPS over ethernet.
Perhaps try moving the USB connector to a different port?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: ReadyNASOS 6.5.0 (RC2) Shows UPS Warning after Installation
I tried moving to the rear right USB port. This made no difference. The NAS no longer auto detects the UPS when connected to a USB port.
It used to work fine with all prior firmware releases.
Am I doing something wrong again?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: ReadyNASOS 6.5.0 (RC2) Shows UPS Warning after Installation
OK, Just for grins I opend the front door of the NAS and connected the UPS to the front port under the cover. It quickly auto connected to the UPS.
I then tried connecting the UPS back to the rear left USB port and the NAS no longer can detect the UPS.
Does this mean I have to keep the front door open all the time if I want the UPS to be connected?
This is not a good solution.
I sure hope the firmware if fixed before release.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: ReadyNASOS 6.5.0 (RC2) Shows UPS Warning after Installation
@McRob1 wrote:
OK, Just for grins I opend the front door of the NAS and connected the UPS to the front port under the cover. It quickly auto connected to the UPS.
I then tried connecting the UPS back to the rear left USB port and the NAS no longer can detect the UPS.
Possibly because the rear ports are USB 3, while the front is USB 2???
Since this worked before, it sounds like a bug that should be fixed.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re : ReadyNASOS 6.5.0 (RC2) Shows UPS Warning after Installation
Hi Everyone,
I have the same problem, I have an email loop about a problem with my UPS, but my UPS is connected.
-----Message d'origine-----
De : Y****s G*****n [mailto:g*****s@o******k.***]
Envoyé : jeudi 5 mai 2016 11:05 À : g****s@o*****k.***
Objet : ReadyNAS Alert Message (homedisk System: Notice)
Cannot communicate with UPS UPS ().
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Installed 6.5.0 RC3 and the UPS is detected again, just like before.
Thanks for getting the fix in.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: ReadyNASOS 6.5.0 (RC2) Shows UPS Warning after Installation
Same issue on my ReadyNas 312, fixed now with RC3