- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Re: Link rate LEDs quit working
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I walked into my home office this morning and found my Apple Airport Time Capsule's ready light was blinking amber. It's connected by Ethernet cable to my EX6200 Range Extender. The link rate LEDs on the EX6200—both of them—are out, but the Device to Extender light is green, as it should be. This setup had been working just fine until this morning—even as late as late last night.
My computer can get its signal from my base router in my living room, but my backup device needs the hard wire connection. I hope someone can help me fix the problem. I updated the firmware about two weeks ago, and everything was in working order till this morning.
Solved! Go to Solution.
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi @Caesar1948,
You can connect to the extender's signal (NETGEAR_EXT) and go through the setup procedure as described here.
Regards,
Dexter
Community Team
All Replies
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Link rate LEDs quit working
Later in the day, I remembered to try unplugging the range extender. Did that, left it for a couple of hours, then plugged it in again. Now my Time Machine backup is working again, green light and all, but the Link Rate LEDs on the extender are still out. Not green or red ... just black. I've checked my WiFi status, and I still do not see the EXT connections available—just "Netgear_EXT" as an open connection (no padlock showing). What's going on?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Link rate LEDs quit working
Hi @Caesar1948,
Welcome to the community!
It looks like the extender is on its default settings. Have you tried reconfiguring it as an Access Point?
Regards,
Dexter
Community Team
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Link rate LEDs quit working
Hello, Dexter, and thank you for replying. This device has worked almost flawlessly just as it was for about three years, maybe longer. All of a sudden it went off track. Just a few days ago, my laptop (MacBook Pro) connected to the Internet via this range extender. As of this morning, I'm using the signal from my Xfinity X1 router two rooms away. Why? I don't have a clue.
To answer your question, no, I have never configured the device as an access point. To be honest, I can't claim to understand the difference. I hope you can help me understand. Anyway, how do I configure it as an access point when I can't get into its dashboard? I tried to enter the dashboard this morning, but it reported that it could not access the device. That makes sense, given that the LEDs are both turned off. I'll appreciate your help.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi @Caesar1948,
You can connect to the extender's signal (NETGEAR_EXT) and go through the setup procedure as described here.
Regards,
Dexter
Community Team
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Link rate LEDs quit working
Good morning, DexterJB:
Thanks for your expert advice. Everything's now back to normal—back-up drive, printer, network. I don't know why it never occurred to me that all I needed to do was repeat the steps that I took back when I first took the range extender out of the box. Duh! The bonus: This exercise forced me to clean up my messy cables and dust behind my desk!
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Link rate LEDs quit working
Hi @Caesar1948,
Thank you for the update. Glad to know you got it working again!
Regards,
Dexter
Community Team
• Introducing NETGEAR WiFi 7 Orbi 770 Series and Nighthawk RS300
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more