NETGEAR Home and Mobile content has changed location. You can find troubleshooting, questions and support resources at https://www.netgear.com/support/home/
My PostsRe: M4300-8X8F uplink to Aruba switchRe: GS105 Letter of VolatilityRe: Thinking about replacing my gs 608 and gs605 with gs prosafe 108 and gs prosafe 105.Re: ReadyNAS 628X - KEYEXPIRED & Hash Sum mismatch - Debian jessieRe: ReadyNAS 2100 FrontView blank page - Firmware 4.2.31Re: IP address NAS not reachable by new modem ReadyNAS Ultra 2 RND2000Re: ReadyNAS 2100 FrontView blank page - Firmware 4.2.31Re: ReadyNAS 2100 FrontView blank page - Firmware 4.2.31Re: Timer Schedule Issue GS752TPP Smart SwitchRe: All 8 WAX610 show as disconnectedRe: GS116 Switch Has Stopped WorkingRe: M4300-8X8F (stacked) with LAG to S3300-28X and VLAN - configuration issuesRe: A Set of clustered S3300-28X need a bit of guidanceRe: Blank web access page for Readynas 1500Re: A Set of clustered S3300-28X need a bit of guidanceRe: Orbi Pro without Insight subscriptionRe: GSS116E will not boot after upgrade from firmware version 1.0.0.2 to 1.0.0.5.Re: Netgear FVS338 service blocking helpRe: Firmware update on M4250 10x10GE SFP+Re: Firmware update on M4250 10x10GE SFP+
Solutions AuthoredSolutionsRe: A Set of clustered S3300-28X need a bit of guidance ChayneC, Welcome to the community! Would it be possible if you could provide a network topology (what ports are the switches connected to each other)? You would generally configure a LA...Re: Fan Noise GS324P DuckNet, Welcome to the community! The GS324P has an acoustic noise level of 31 dB given that the switch operates at 25°C in which it is generally considered to be quiet. The same thing goes ...Re: GS308T LACP Setup problem with TrueNas Server madars, Welcome to the community! Could you also provide the LACP configuration for the TrueNAS? Also, please verify if the LACP configuration on the TrueNAS has the same hash mode as the...Re: Unable to login to my new SXR80 Orbi Access Point DaleDurnell, Welcome to the community! Since the SXR80 was set to AP mode, what will happen is that the SXR80 will get an IP address from your RAX80 and so what you can do is go to the "A...Re: WAC720 and WAC730 Hi JrBK, Yes, it should work (you may refer to page 87 of the user manual here under Set Up, Manage, and Monitor Ensembles). As for configuring it, you may check these resources as well: ...Re: ReadyNAS 102 Communication Error when checking for Updates Hi! It should be fixed now. Please let us know if you're still encountering the issue. Regards, JeraldM NETGEAR Community Team Re: DNS error message 6001010060 readycloud login and admin page Hi! It should be fixed now. Please let us know if you're still encountering the issue. Regards, JeraldM NETGEAR Community Team Re: update.readynas.com down? Hi chri6020, Please see this related community thread for more information. Regards, JeraldM NETGEAR Community Team Re: Setting up a small WifI network using WNDAP360's Hi Marhan05, It is possible to setup the WNDAP360s to have client devices connect from one AP to another by configuring the APs with the same SSID as you said. However, the APs are fairly...Re: GC752X Switch Login Failure Hi akio63, Were there any events that occurred that may have caused this issue the first time you noticed it? Would it be possible to update the FW of the switch to v1.0.5.35? Have you al...
My Most Liked PostsMost LikesRe: ReadyNAS 102 Communication Error when checking for UpdatesRe: ReadyNAS 2100 FrontView blank page - Firmware 4.2.31Re: DNS error message 6001010060 readycloud login and admin pageRe: ReadyNAS 2100 FrontView blank page - Firmware 4.2.31Re: RNDP600U upgraded to OS6 stuck at ReadyNASRe: ReadyNAS 524X vulnerability?Re: GS116Ev2 - Can't log into Prosafe - Command is not supported by agentRe: Replicate BackupRe: Thinking about replacing my gs 608 and gs605 with gs prosafe 108 and gs prosafe 105.Re: ReadyNAS 2100 FrontView blank page - Firmware 4.2.31
