NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
POST Issues GSM4248UX
Hi, the power on start of self teset on my GSM4248UX is failing. I power on the switch and it starts with the test. All of the ports in the back of the unit light up for a few seconds. The power LED blinks a number of times then stays on red solid light. The switch is not accessible via the OBB or any of the ports. The switch was working fine for a day or tow, but then we updated the software to the latest firmware. V13.0.5.24 Then we started having this issue. I have tried the paper clip reset multiple times, but there are no indications that this is working at all. Any comments will be greatly appreciated.EX6130 Configuration
Bonjour, Depuis que je suis passé d'une box ADSL Freebox à une BOX SFR 5G (4G+ également), je n'arrive plus à avoir un fonctionnement stable de mon répeteur WIFI EX6130. La connexion en 5Ghz ne fonctionne pas et la connexion en 2,4 Ghz se déconnecte régulièrement. Je précise que j'ai procédé un reset plusieurs fois et installé le répéteur suivant la procédure de NetGear. Merci pour votre aide.WAX630E LAN to 2,5Gbe
Hallo Leute, mein WAX630E hängt an einer intel x550 Nic und der Autospeed handelt 1Gbe mit dem AP aus, wenn ich den LAN Speed auf 2,5Gbe setze gibt es keine Verbindung zum AP. Scheinbar gibt es keine Kommunikation zwischen beiden Geräten wenn ich den Speed auf 2,5Gbe setze. Kann ich den AP auf 2,5Gbe LAN Speed setzen? Ich nutze die Insight configuration via cloud. Mit freundlichen Grüßen RenéHelp understanding the "Set the 802.1Q VLAN and management VLAN" WBE750
On my router I have a X550 interface tagged with a vlan ID of "4" which attaches to my switch port as a "trunk port with a vlan id of "4"" on the switch I have an "access Port with a vlan id of "4" that is connected to my "WBE750" RJ45. In the LAN settings of the WBE750 Do I place the vlan id of 4 in the "Untagged VLAN" setting or the "Managed VLAN" setting. Any assistance would be greatly appreciated. Best Regards[MS108TUP] - Switching - VLAN and routing
Hello everyone, I've this network configuration: Firewall --> MS108TUP --> Access Point Wifi The firewall and the AP is not a Netgear product. I've a domotic house so I've decided to separate the smart devices from the Main network. So in this case I've created an dedicated AP SSID with VLAN ID 20 only for manage smart devices. My network is also managed by a dedicated firewall device that manage VLAN Interfaces, WAN Interfaces, LAN Interfaces etc etc. Throught this Firewall, manage all the L2/L3 levels, from DHCP (one for every interfaces) to Privacy control, from Captive Portal (for Guests account) to Policy Control rule, ACL, Static route, QoS etc etc. So, I've configured the MS108TUP with several VLAN created in Switching mode (Switching --> VLAN). This is my current VLAN configuration on MS108TUP: MG1 is the Firewall uplink port, instead MG2 is the AP Uplink port. And this is the configuration of the interfaces into my Firewall: In this way, the AP create a SSID with VLAN 20, MG2 take the VLAN 20 and route it on MG1 VLAN 20; the firewall (MG1) take the VLAN 20 on port P2 and create it's own network with it's own dedicated DHCP and Static IPs list. All works good but when, from the firewall, I try to block traffic from/to the same interface/zone, not working. For example, if I try to block the SSH port from the tablet to my Raspberry PI and the tablet and the RPI is in the same interface/zone, the traffic is not blocked (my rule is: from DomoDevicesVLAN to DomoDevicesLAN source "tablet" destination "RPI" any service --> deny ----> this rule must deny the traffic for any service from the tablet to the RPI "using" the same zone but not work). Seems because the packet traffic is directly managed by the MS108TUP. Seems as the request is not passing throught the firewall, but remains at the switch level. For example: 192.168.0.5 --> 192.168.0.6 directly In this way the traffic is bypassing the firewall, because remain into the "switch" level Instead, how I can route the traffic thought the firewall? 192.168.0.5 --> 192.168.0.254 (Firewall interface) --> 192.168.0.6 In this way the traffic must pass into the firewall, and in this way I can have full-control on the packets and I can apply a Policy Control rule. Thank you so much Best Regards, Valerio
M4300 (GSM4352PS V1) : can't get kernel image
Hi Netgear Users and Administrators, I have a little problem with my M4300 GSM4352PS V1. There's possibility that image2 is broken. Device is actually booting from image2. On the console I see that can't boot from image and i see "ERROR: can't get kernel image". I supose that the image1 is a good conditional. Best Redgards Pawel